Older Folks and Vaping Front Porch - Part Four

Status
Not open for further replies.

Debadoo

ECF Guru
ECF Veteran
Verified Member
May 18, 2012
18,052
133,969
Texas, near Fort Hood
Love it!! Of course, I'd have to customize it with a Reo and a Derringer or Nuppin! Would love to have one of those and the Politician one, but even if I had it, I can't see spending that kinda $ on Tshirts. Well, the customized, cuz they're probably a lot. Now if I won the lottery or sumpthin, I'd get us all one! lol So glad you posted those! Made me happy to see folks are doin that!
 
Last edited:

Iffy

Vaping Master
ECF Veteran
Verified Member
Feb 3, 2011
9,626
79,411
Florida Suncoast
Oops, here's my hat, don't care who knows I'm angry. :D

71TTsud9LvL._UY500_.jpg

Who woulda thunk! From feathers to tassels... <sign o' da times, sigh>


Check your couch and see if that much is under the cushions.

And there's a 50% off sale today only.

WOW, tuphph decision... Super Bowl ad or a half ophph t-shirt.

I'll get back wid ya'll later...
 

Debadoo

ECF Guru
ECF Veteran
Verified Member
May 18, 2012
18,052
133,969
Texas, near Fort Hood
Yeah even with the half price sale still kinda pricey. And then you still got shipping. I don't wear t's at all.
the 1/2 price makes it much better forgot about that, but I didn't check the custom price, but noticed the other two were 26.00 or so but the politician one was 45.00 But they're great! If I had it to spare, I'd go for at least one!
 

EBates

Vaping Master
ECF Veteran
Nov 4, 2013
3,858
4,659
Texas
How can you fill a v2 from the top? If you unscrew the top the chimney & sometimes the base come with it.

It all goes back to when you rewick the KFL or KF3.1. Tighten the evap chamber wall and chimney tube. I've only had the chimney tube come loose while removing the top cap once in over a year of using the KF 3.1s and never with the KFLs.
 

EBates

Vaping Master
ECF Veteran
Nov 4, 2013
3,858
4,659
Texas
'When I open up my Orchids, the chimney stays in the tank about half the time. I don't mind. That means I have a good seal between the topcap and the top of the chimney.

I agree, but it can become a problem if you top off the tank and find out that the chimney tube is not tight i.e. allowing juice to enter the evap chamber. Been there dun that.
 

Iffy

Vaping Master
ECF Veteran
Verified Member
Feb 3, 2011
9,626
79,411
Florida Suncoast
WOW, tuphph decision... Super Bowl ad or a half ophph t-shirt.

I'll get back wid ya'll later...

OK, after further close scrutiny of Matt's vid, think I'll go wid da halph ophph t-shirt option! Beside, da couch didn't ¢ough up much...
 

Kenna

Vaping Master
ECF Veteran
Verified Member
Aug 14, 2014
7,367
121,493
Texas, USA
I have a set of screwdrivers that has a small one with big enough handles that there is no fumbling around. The base spins so you can put the tip of your index finger on the end and rotate it with your other fingers, tip of the screwdriver is pushed into the head of the screw (Hope that make sense). The tip and shaft are the perfect size for the screw and you could use it to wrap a coil too.

Careful, you'll get Iffy wound up again.

Probably about 2mm in diameter.

Never mind.

Works great and stays on the kitchen counter with the rest of my vape filling gear. I have a small zippered pouch that holds two 30ml juice bottles, my blunt tipped fill syringe, that screwdriver and a 2 pack of 18650s perfectly.

Admit it. It's a fanny pack!I


also have a small (tiny) zip lock bag that came with my Kayfuns with a few extra screws and O-Rings in there too. You know the 1 1/2" square ones that came with them. Whole deal slides right into the cubby in the console of my car. Got the screwdriver set at Harbor Freight of course. It's the one on the left in the pic.
6 Piece Precision Screwdriver Set with Molded Handles
 

Robert Cromwell

Moved On
ECF Veteran
Feb 16, 2015
14,009
65,472
elsewhere
Hope to get to try out my Lemo 2 sometime this weekend.
Got the wheelchair ramp done finally... Well useable anyway. Just have 4 inch high bumper strips on the edges so far. Still need to add handrails...
My back hurts...
The wife unit will not be going out un-escorted for a while so no problem.

Just realized I have 3 toppers that require drip tips so now something else to buy....
I am short 1 right now since the Velocity Mini did not come with one. Using one from my little Caterpillar dripper on it for now. The velocity had a chuff tip but I have no use for that thing. Will likely just use the Velocity for juice testing, Dripping is a pain, I have enough trouble not running a tank dry...

Molehill Mountain? Naah too expensive but nice tips.

flavor got a bit better on the second tank in the STM, maybe up to my T3 flavor now.

Also I need to get an ohmmeter now with these rebuildable heads. One thing just leads to another. My old fluke is just not good enough at low ohms for it maybe I need new leads...

Well enough rambling, good night all. Have to go get the wife unit from rehab tomorrow.
 
Last edited:

Kenna

Vaping Master
ECF Veteran
Verified Member
Aug 14, 2014
7,367
121,493
Texas, USA
oh lordy, hope you're back up and running soon, that's awful hun. And uhmmm.....I may not wanna know, but how on earth did some guy piddle for you??? It's crazy that happened, and they didn't know! I'm with Iffy, that is inexcusable on their part to have let that happen

What guy doesn't walk into a restroom, see an empty lab bottle with someone else's name on it, & not think it would be good to pee in it?
 
Status
Not open for further replies.

Users who are viewing this thread