They.ll line up, but it's best to tighten that 520 pin more to do that rather than loosening it. I've had 2 that I had to take apart & reinstall that 5 10 to get itto thread right to get the holes lined up.
Older Folks and Vaping Front Porch - Part Four
- Thread starter MikeE3
- Start date
- th_trl_thread_readers 0
- Status
- Dec 18, 2013
- 2,946
- 56,640
- 79
But seeing the clip through the fill holes rules out a blockage there. Some of my dual intakes I can see through, some not, and I've not noticed a difference in draw... as seems to be the case for you with the one that's working well.
Perhaps something in the drilled portion of the 510 pin? You'd need to take the coil off to check that. Paper clip trick may work, but you may need to remove the pin.
How long are you leaving your wick? It should just touch the bottom. And be kept away from the opening on the pin.
If going that route, be careful not to overtighten. Chance of breaking the pin.
I guess I've seen you "around" and didn't realize you hadn't posted on the porch before.
Just want to welcome you to this wonderful group and say I'm very happy you've decided to join us. I remember you, Jumper. Four pages? Really, we did four pages? Eight is more the norm for us, you sure you didn't miss a few?Been here be four, just don't post much but after 4 pages of funnels I thought I would throw in my. I think it worked
Nude Nicotine has a sale through Monday night. Code is "2016IsOurYear"
will apply a 25% discount on all NICOTINE BASES AND FLAVOR CONCENTRATES! Applicable to all nicotine strengths (including 100mg/mL), ARMOR v1 + ARMOR v2, and all aliquot sizes 500mL or below. Remember, shipping is ALWAYS FREE on orders over $100
Iffy, it's your birthday?
Happy Birthday Iffy!
In all seriousness, I do hope you have a wonderful birthday, you deserve it my dear friend.
@Iffy - Happy Birthday my friend
@DancingHeretik - arrgh re: you KFL issues, I'll be back after the coffee kicks in and my mind starts functioning.
@DancingHeretik - arrgh re: you KFL issues, I'll be back after the coffee kicks in and my mind starts functioning.
@DancingHeretik I just took 2 of 'em out of the box that arrived last week. I did get them from Fluid Vapes.
The airflow seems right when drawing on them. If I just try looking through the two side air holes I don't see through them. But if I hold them up to a light when looking - in one I see a pin hole sized spec of light, the other even a smaller pin hole of light coming through. Both seem to draw OK.
But what I did find - on one of them, the air adjustment grub screw just spins in the hole it won't go in or out. Threads must be stripped. At least its flush w/ the bottom of the atty so I can just leave it there and not worry about it coming out.
Maybe I try contacting Fluid Vapes for an exchange they seem to still have some in stock now at ~7$ each.
Last edited:
I got mine from different vendors at different times including last month from vapor range & I had to adjust the 510 in several. All of mine are Ehpro. You should be able to hold them up to a light & see a perfect circle of light. If it's not a circle then the airflow is being chocked at the 510. All it takes is a vert tiny adjustment of the 510 clockwise or counter clockwise to fix it. I had 2 that had no airflow at all. I hade to take the 510 out completely & rescrew it holding the positive post tight to the deck with a pair of slip adjustable pliers. Once it was fairly tight, I lined up the positive block where it should be & finished tightening & lining up the airholes. Everything fell into place & lined up & stays tight. I just had to do it from square one. I havent checked the newest ones yet.
huh ... I never checked any of ours and they all seem to be working OK. I'll have to pay attention to it as I rewick and/or rebuild them. This morning was the 1st time I looked into this trying to help Dancing.
- Dec 18, 2013
- 2,946
- 56,640
- 79
Ok, so why does attention get a commission when yer rewickin'? And what eggzackly is said commish? Or, as me old granmudder used to say... how much cost sucha kinda ting?
I had the weirdness too. On one of the other threads (back porch?), the suggestion was to go to the bottom of the page - on the left hand side you'll see ECF or E-cigarette Forum. Click on that - it will say Style Chooser. I managed to reset my screen back to my usual look. Phew.
Dang, Lannie, something must have happened, as there seem to be a lot of similar comments this AM!
Scroll down to the bottom of the page, bottom left will say something like ECF, ECigaretteForum or ECigaretteForumDark. Click it to check out and set the skin you like.
I'm wonder if they changed the "default" to ECigaretteForum.... where ECF was the old default.... I'd tried the two new ones a few weeks back, then reset the original for my default. Perhaps the act of setting it in my prefs over-rode any other changes.... so if you've not set a default, you' re subject to any changes they make in the board software....
I was told about it by some who pif'd me a couple. She said a lot of them need adjusting d to check new ones.
Dang, Lannie, something must have happened, as there seem to be a lot of similar comments this AM!
Scroll down to the bottom of the page, bottom left will say something like ECF, ECigaretteForum or ECigaretteForumDark. Click it to check out and set the skin you like.
I'm wonder if they changed the "default" to ECigaretteForum.... where ECF was the old default.... I'd tried the two new ones a few weeks back, then reset the original for my default. Perhaps the act of setting it in my prefs over-rode any other changes.... so if you've not set a default, you' re subject to any changes they make in the board software....
That was it! THANK YOU!
It's all back to normal now - I changed it back to "ECF." I never had scrolled that far down the page, EVER, to even see that 'style chooser' link! I had no idea it existed. Thanks for the tip!~Lannie
- Dec 18, 2013
- 2,946
- 56,640
- 79
Well that's grate. But... u killt da tred.Great, I killed the thread... I made juice today! 180ml total, three flavors.
- Status
Similar threads
