Older Folks and Vaping Front Porch - Part Three

[2legsshrt]

2legs what build do you have if any in your subtank mini rba section ?

I did 2mm cause figure its a small area , went meh , now have a 2.5mm and it seems better.
Though with the same juice its no where near the goblin.
Also on the RBA section where do you have your coil ,,,, you got the air hole then the two metal bits with the screws , do you put the top of the coil in line with the top of the screws or have it higher so the bottom of the coil is in line with the top of the screws , or do you not think about it ?

Many times Im getting very little vapor and yet no dry hits, could be its small juice holes but would expect dryish hit but its fine just not much vapor at times.

I have put 3mm no prob. Right now I have a 7wrap 2.5mm 26awg in on for 1ohm. The others I have 28awg 2.5mm 6 wrap for 1.5 ohm but I like the vape with the 26 so much better I'm going to change the one in my DNA40 to that too. But there is plenty of room in there for anything, 3mm is my largest but I really like the 1ohm with the 26. Run it at 14w in Powerful Mode in my SXmini and that 2 second preheat really makes for a good vape. It just starts to get warm and cuts back to the 14w I have set and it is just right.

 

[2legsshrt]

Hi Darryl
Mines twitchy if the wick blocks the holes. Any wick near holes gets dry , if wicks flick out from where I've pasted them to the deck and block the holes it gets dry.

I put the bottom of the chimney on and cut the wick to about 1/2" beyond the chimney and poke it down then wet it and fire it wet it again put the top piece on and put it together have had no problems. Ever almost exactly like I do my Kayfuns. I do make sure I get the tips of the wick down first so they are just touching the air holes and puffed out. I don't poke it in hard just loosely.

 

[2legsshrt]

That 12 wrap 26awg 2.5mm I accidently put in was too much of a battery eater. 1.6ohms and that much 26awg doesn't get warm real fast. Had to run it at 16-18w which was 5.2v or so. Now with the 1ohm at 14w its only 3.8v. Considerable diff.

 

[2legsshrt]

La Vapeur, I like that one1

Pepe LePeus vapor shop

 

[2legsshrt]

I also think the coil comes out a little higher then the screws. I will check it when I go up and change the DNA40. I do put the coil on so the legs are on the bottom but it might get pushed down a little when I am straightening it.. I pinch my coil now with the needlnose and torch it with the 26. I can do it on the mod with the 28 but the 26 is a little tougher to get squeezed good with tweezers.

 

[2legsshrt]

Oh I am still vaping on my rebuilt head still working perfectly. I need to get on it and make a 5 wrap at 3mm with my 27awg think I can get a 1.2 5 wrap seems to be the ticket for good vaping. The 28 gives me 1.3 which is really good. I really can't remember how many wraps I used but it sure works good. I think it is 4

 

[Metal Storm]

Got some unflavored 18mg nic to use in my Nautilus at work. Every flavor I take to work ends up getting tiresome so I figured this might work and it's good so far.

Vaping on some Cinnagram custard from ITC Vapes right now. Didn't like it at all in the Subtank but it's a nice vape in the Doge. It was too sweet in the Kanger but it's about perfect now. 50/50 throat hit is a little harsh in a dripper but I love the vape I get from this RDA. Using the Subtank is like vaping through a coffee stirrer compared to the Doge. It goes through the juice like crazy though. Sat here and vaped 10ml in a few hours last night!

Going out for my nightly walk / jog. Have a good night, my friends.

 

[Ken_A]

OK - I'm out of the loop on tech issues with vaping...
but I KNOW we have experts here.
PLEASE comment on the FDA workshops
http://blog.casaa.org/2015/03/call-to-action-submit-comments-on-fdas.html

 

[Wolfenstark]

Perhaps it could help but it is hard to educate someone who thinks touching something at 35F could be as damaging as touching something at 212F

 

[Doffy]

I've got a grey wrinkle and a copper wrinkle if that helps

Probably not then. TRA or anodized fit the 2013 cyclones sans afc

Sent from my GT-I9506 using Tapatalk

 

[Ken_A]

Perhaps it could help but it is hard to educate someone who thinks touching something at 35F could be as damaging as touching something at 212F

you could PM me with your info, and I would be happy to gather it together for them. the only way to assure you lose a fight is to not fight at all.

 

[LittleBird]

Thanks for posting the link, Ken. Somehow, my calls to action banner disappeared ...

 

[Ken_A]

Thanks for posting the link, Ken. Somehow, my calls to action banner disappeared ...

You most likely accidently hit the "x" at the top right of it..
Here is the link to the calls to action
http://www.e-cigarette-forum.com/forum/casaa/531683-calls-action-roundup-updated-3-17-2015-a.html

 

[2legsshrt]

Well my Tugboat saga is coming to an end it is out for Delivery today.

 

[Debadoo]

Probably not then. TRA or anodized fit the 2013 cyclones sans afc

Sent from my GT-I9506 using Tapatalk

I had no idea a particular finish would matter, just thought it was the Reo style. Or am I misunderstanding?

Well my Tugboat saga is coming to an end it is out for Delivery today.

Glad you're finally getting it!

 

[Doffy]

I had no idea a particular finish would matter, just thought it was the Reo style. Or am I misunderstanding?



Glad you're finally getting it!

The wrinkle coating is thicker, which takes away from the catch cup

Sent from my GT-I9506 using Tapatalk

 

[Debadoo]

The wrinkle coating is thicker, which takes away from the catch cup

Sent from my GT-I9506 using Tapatalk

Good to know! Thanks!! Never ever woulda thunkit!

 

[Metal Storm]

Well my Tugboat saga is coming to an end it is out for Delivery today.

It's about time that Tugboat set a course for your house. I look forward to hearing how you like it.

 

[clnire]

Well my Tugboat saga is coming to an end it is out for Delivery today.

You sure it is out for delivery at your house?

 

[3mg Meniere]

You sure it is out for delivery at your house?

Maybe it is out for delivery somewhere in Kansas.