Post pictures of your working wick and coil setup

[The.Drifter]

Been awhile since I did a coil build sequence photo bomb so I thought I would share my Lancia build

I used all the 3mm air posts to go with my wide bore drip tip, lots of airflow for this build

Dual 26G spaced coils over 3mm screw came out to 0.48 ohms. On a fresh battery 4.2 Volts = 8.75 Amps at 36.75 Watts

For my spaced coils I like to use a screw to keep everything even:

Shot of the Duals after wrapping:

Side shot of a coil:

I use the screws to help mount the coils:

Shot of the mounted coils from the top:

Mounted coil shot from the side:

Couple shots of test firing

Medium glow:

more power to it:

I use Rayon for the wicking, shot of it pulled thru and trimmed to be fuzzy:

Wick juiced and tucked:

Wick chambered:

Final build shot:

 

[havok333]

Been awhile since I did a coil build sequence photo bomb so I thought I would share my Lancia build

I used all the 3mm air posts to go with my wide bore drip tip, lots of airflow for this build

Dual 26G spaced coils over 3mm screw came out to 0.48 ohms. On a fresh battery 4.2 Volts = 8.75 Amps at 36.75 Watts

For my spaced coils I like to use a screw to keep everything even:

Shot of the Duals after wrapping:

Side shot of a coil:

I use the screws to help mount the coils:

Shot of the mounted coils from the top:

Mounted coil shot from the side:

Couple shots of test firing

Medium glow:

more power to it:

I use Rayon for the wicking, shot of it pulled thru and trimmed to be fuzzy:

Wick juiced and tucked:

Wick chambered:

Final build shot:

Nice looking spaced coils! Loving the look of that Lancia too.
[emoji41]

 

[Dristwaz]

Just got my Ruler RDA in the other day and here's my quad coil set-up that I'm going to try once the battery is done charging. What do you all think?

 

[Dristwaz]

Ok, here's the pic attached this time, I think. Super slow internet sucks.

 

[Mikepresjr]

Current build in the Hobo V2.1:

Dual Coil 28G Kanthal 7 wraps, vaping with strawberry orange banana.

Sorry they're dirty, it's had a few days use.

 

[SLIPPY_EEL]

Nice Lancia's and builds, i wasnt gonna get one but you gotta spend money on something, right? lol

Can one of you lucky Lancia guy's give me the dimension's on the height of the glass and the id or the thickness of the glass, i know it's 22mm

 

[G-weezy]

Are you trying to see of the chuff top will fit? I have a Lancia and this thing rocks.

Did a little tinkering on the AF plugs.

Before

After

Vape check

 

[SLIPPY_EEL]

Hey Weezy, does the chuff fit?

i was asking for the dimensions as i have some glass barrels on the way with the clone from fast tech as they only have the lancia with the metal barrel so far

 

[Mikepresjr]

That last shot had no flash, this one kind of helps a tad:

 

[t2ak]

Build for my Hana. Was going for a single macro coil and slipped and stretched it out. I took some time to clean it up and it came out awesome.

26g 11 wraps around 0.125 drill bit

Sorry no glow shots. I didn't think to take pictures until I had it wicked.

The Giraffe

 

[G-weezy]

Hey Weezy, does the chuff fit?

i was asking for the dimensions as i have some glass barrels on the way with the clone from fast tech as they only have the lancia with the metal barrel so far

No it doesn't fit. I tried last night lol. I'll get measurements for you after work.

 

[JoeVan]

Not sure what to call this one, as I have not seen it done by anyone else. If anyone knows, please tell me. Until then, I am going to call it the "Stark Coil" because fired up it looks like Tony Stark's cave-built Arc Reactor from the Iron Man movie.

Looking for clouds and flavor?? Try this one out, it performs amazingly. I built it just for .....s and Giggles, but it ended up actually producing some awesome results. First fire looked like I was trying to seduce a little she-dragon.

12 wraps total (24 if you build both sides of your RDA), 24g A1 Kanthal, I guess it would be considered "parallel".. 2 wires each post, 4 throught the middle. Built on a IGO-W, sitting atop a K100 (old reliable, unbreakable, ugly thing). Top cap barely fit. Calculator says it should be .32 ohms, but I haven't tested it yet.

Disclaimer: I DO NOT RECOMMEND DOING DUALS (really, quads) ON THIS BUILD. (not with 24g at least) My button got red hot after 3 pulls so I scrapped the 2nd side and went back to the single side parallel. It hits damn good with just the one side.

 

[TheKiwi]

Lol. Haven't tested it yet and button got red hot?

Not enough hands or face to give sufficient face palms


Burping out loud using Tapatalk

 

[JoeVan]

Lol. Haven't tested it yet and button got red hot?

Not enough hands or face to give sufficient face palms


Burping out loud using Tapatalk

I'm using VTC4's I can go down to .2 and I ohmed this out at .3 on the dot. Running duals, that would come out to .15, which still falls within the pulse rating of the VTC4's, I just don't care to risk it (hence, me dropping back down to the single side build).

I may be a "noob" on this forum but I have been building for a good while now. On a K100 my button can heat up from a .4 build, and still be safe, so don't take it out of context. Maybe red hot was an exageration. It got warm, enough to make me stop and rebuild. Vape safe.

 

[G-weezy]

@slippyeel,

 

[SLIPPY_EEL]

Thank's Weezy

the chuff will fit if you take a file to it though, i have something like 20 odd chuff's i dont mind butchering one to fit, i have chuff's on my mutationX's, and not that i will but if i wanted to make em fit the attys they were made for then all you need do is put the o-ring back in

 

[G-weezy]

I hear ya on that. I only got one Chuff. That was an expensive one. Right after I got mines they flooded FT with them . On my next order will be a bunch of them.

 

[SLIPPY_EEL]

I hear ya on that. I only got one Chuff. That was an expensive one. Right after I got mines they flooded FT with them . On my next order will be a bunch of them.

hahahaa yeah cus FT is so cheap i bought 5packs of clear, white & black. i really like my 26650 chuff for my asmodus, the bigger chuff's have the same id DT as the 22mm's. i have a couple of they metal chuff's on the way also that have extra fin's, also have some plastic chuffs without fins but it sits you to close to the coils if you ask me unless its on a 26650 without fins then its ok LoL. chuffchuffchuff

 

[zipflint]

Dang. You folks have some REAL artistic talent and GOBS of patience! I'm fairly content with this run-of-the-mill 0.4Ohm not-so-micro-coil in this Lancia clone.

Lancia clone 0002 by zipflint, on Flickr

Lancia clone 0006 by zipflint, on Flickr

Lancia clone 0003 by zipflint, on Flickr

 

[SLIPPY_EEL]

they are some real clear pics