I love them all, but my favorite would be 30mm Wolverine. Because it took most time and effort to make it the way it is now.
- Status
I love them all, but my favorite would be 30mm Wolverine. Because it took most time and effort to make it the way it is now.
28g, 1/16, dual, 12 wrap, Rayon.
I had trouble with dual Diamond's being to hot in my mech, now i can do it on this and its pretty darn nice
I had trouble with dual Diamond's being to hot in my mech, now i can do it on this and its pretty darn nice
28g, 1/16, dual, 12 wrap, Rayon.
I had trouble with dual Diamond's being to hot in my mech, now i can do it on this and its pretty darn nice
The sigelei is going to be my next purchase. Say I ran a .3 build,can I get a full day off of it? Jeeze....havent used a electronic mod since the huge tube style
Last edited:
Decided to do a basic build for once lol. Dual 8 wrap 24 gauge around a 21 gauge needle. Came out to .18 ohms.
How's that big dripper clone, I've been wanting to pick one up, a clear tank section is a big plus.Big Dripper V2 from FastTech
how ya been sloppy, gonna try a diamond coil again soon im thinking 22, or 24g. Of course i need it to be above .3 for my raptor, and probably dual setup. Well crap might have to go higher gauge. Or dust off my mech....28g, 1/16, dual, 12 wrap, Rayon.
I had trouble with dual Diamond's being to hot in my mech, now i can do it on this and its pretty darn nice
[]http://i1025.photobucket.com/albums/y320/SLIPPY_EEL/DSCF5005_zpsbe1e1d43.jpg[]
[]http://i1025.photobucket.com/albums/y320/SLIPPY_EEL/DSCF5006_zps8225d7e4.jpg[]
[]http://i1025.photobucket.com/albums/y320/SLIPPY_EEL/DSCF5012_zps99774675.jpg[]
It vapes very nice and having almost 5 ML in the tank always helps. Built deck is like Omega RDA.
BUT this particular FastTech clone SKU: 1896002 had some problems: https://www.fasttech.com/p/1896002
1. One of the negative posts was NOT threaded at all. And the grub screw was jammed in unthreaded hole. I had to drill the jammed screw out and Tap M2.5 - 0.45mm new threads. Luckily some extra grub screws were included. But those screw are attracted to magnet and therefore may not be Stainless Steel. I'm replacing them with these: http://www.amazon.com/gp/product/B00B3RJKKK/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1
2. The hole, where the drip tip goes, is too small and none of my over 100 drip tips fit in it. I had to widen that hole.
But that cold be just in my particular unit, the rest of them might be good. I doubt it.
Last edited:
Here's my first satisfactory build on my Squape R clone. Diggin' this doo-dad a lot!
My coil got a bit mangled due to my clumsiness, but it's still lighting from the center, out, with no hot spots. My first few builds, I had too much rayon in the channels (I'm using the "Wide" base) and was getting a dry hit every now and then. This appears to be the sweet spot as far as wicking goes.
SQuape Reloaded clone 0003 by zipflint, on Flickr
Here 'tis on my Wotofo ZNA clone.
SQuape and ZNA clones by zipflint, on Flickr
My coil got a bit mangled due to my clumsiness, but it's still lighting from the center, out, with no hot spots. My first few builds, I had too much rayon in the channels (I'm using the "Wide" base) and was getting a dry hit every now and then. This appears to be the sweet spot as far as wicking goes.
SQuape Reloaded clone 0003 by zipflint, on FlickrHere 'tis on my Wotofo ZNA clone.
SQuape and ZNA clones by zipflint, on Flickr
Last edited:
Erlkonigin 0.6mm X 0.1mm Flat Ribbon NR-R-NR with Rayon (Double Inserted)
And a little extra silicone 510 insulator
And a little extra silicone 510 insulator
Nice whats the difference between v1 and V2.
I really want this one though because of the glass tank, and smaller 2.5-3.5ml capacity http://www.fasttech.com/products/3028/10009819/1926201
Heres most recent build
Dual 28g .6-.7ohm, 5/64th ID, single tail rayon wick.
Pulled the trigger on a couple FT clones (thanks AMD for the confidence) https://www.fasttech.com/products/1958800 Kayfun Nano V3 Style RTA Rebuildable Tank Atomizer (4ml)
http://www.fasttech.com/products/0/10009819/1930802-big-dripper-v2-style-rda-rebuildable-dripping Dripper V2 Style RDA Rebuildable Dripping Tank Atomizer
Can't wait to get them and start building them and wicking them with the amazing do everything rayon.
On a down side somehow when i ordered it processed the order a additional 2 times and charged my card for it..... I've put in a ticket and expect a refund within 48hrs as the website states..... But with them being on Hong Kong time, its already Saturday i hopen they work weekends lol.
*edit* oops wrong thread oh well
http://www.fasttech.com/products/0/10009819/1930802-big-dripper-v2-style-rda-rebuildable-dripping Dripper V2 Style RDA Rebuildable Dripping Tank Atomizer
Can't wait to get them and start building them and wicking them with the amazing do everything rayon.
On a down side somehow when i ordered it processed the order a additional 2 times and charged my card for it..... I've put in a ticket and expect a refund within 48hrs as the website states..... But with them being on Hong Kong time, its already Saturday i hopen they work weekends lol.
*edit* oops wrong thread oh well
Last edited:
The difference is just that: V1 is solid Stainless, V2 has clear Plastic tank and can be filled from the top (more liquid and convenience)
I also wanted the glass one, but it has a lot of BAD reviews.
Erlkonigin 0.6mm X 0.1mm Flat Ribbon NR-R-NR with Rayon (Double Inserted)
And a little extra silicone 510 insulator
Very nice bro.
I started hating my Kayfun for lack of Airflow and here is what I did today:
The Airflow is now 2.6mm, was 1.6mm
The Airflow is now 2.6mm, was 1.6mm
You got any extra parts I can buy from you for the 3.1 mod? Would love to try this thing out.
No sir, I don't make them for sale. These are just for my own personal use to return my Kayfuns back from retirement. They Vape much like Lemo, Erlkonigin, Squape R. Not much difference.
Here's one of many I've been playing around with lately. Twisted 28 alongside 24g paralleled, 6 wraps per side, 1/8" ID, .18Ω.
The vape is not as dense of clouds as most builds this low but it still keeps a good flavor. Also heats up suprisingly even!
The vape is not as dense of clouds as most builds this low but it still keeps a good flavor. Also heats up suprisingly even!
My Vapor Flask burnet out. Smoke came out and it is dead now. Went back for RMA.
Nothing beats this Big Kayfun on a Mech. Now that it has 2.9mm Airflow!
Nothing beats this Big Kayfun on a Mech. Now that it has 2.9mm Airflow!
This is my first build on the Veritas clone. It's working great, but I'm open to suggestions.
Veritas clone 0001 by zipflint, on Flickr
Veritas clone 0003 by zipflint, on Flickr
It matches up well with my trusty old brass Sentinel clone.
Veritas clone 004 by zipflint, on Flickr
Veritas clone 0001 by zipflint, on FlickrVeritas clone 0003 by zipflint, on FlickrIt matches up well with my trusty old brass Sentinel clone.
Veritas clone 004 by zipflint, on Flickr- Status
Similar threads
