That's the beauty of digital photography. Even if only 4 out of 20 photos are good, you always come out ahead!
they are some real clear pics
- Status
Thank's Weezy
the chuff will fit if you take a file to it though, i have something like 20 odd chuff's i dont mind butchering one to fit, i have chuff's on my mutationX's, and not that i will but if i wanted to make em fit the attys they were made for then all you need do is put the o-ring back in
not to sound too nubish but whats a chuff?
Does anyone have a coil idea for the "lil boy" or has anyone found a good setup for it?
It's third party extra extra extra wide drip tip/top cap combination .
http://www.kidneypuncher.com/chuff-style-drip-tip/
My first Clapton coil.
Hand wound.
24g inner 30g outer
2.5mm id 5 wrap
0.6 ohm
Cellucotton
Tugboat v2 - Manhattan
The start.. (Also the first shot)
Halfway there (beer and two shots later)
Not too shabby IMO (lost track lol)
Flavor town!
The Giraffe
Hand wound.
24g inner 30g outer
2.5mm id 5 wrap
0.6 ohm
Cellucotton
Tugboat v2 - Manhattan
The start.. (Also the first shot)
Halfway there (beer and two shots later)
Not too shabby IMO (lost track lol)
Flavor town!
The Giraffe
Really nice setupMy first Clapton coil.
Hand wound.
24g inner 30g outer
2.5mm id 5 wrap
0.6 ohm
Cellucotton
Tugboat v2 - Manhattan
The start.. (Also the first shot)
Halfway there (beer and two shots later)
Not too shabby IMO (lost track lol)
Flavor town!
The Giraffe
I decided to modify my Lancia 1:1 clone from FC by replacing the Air Tubes with longer ones that I made from 304 Stainless Steel.
4mm outside and 3mm inside diameter, 10.5 mm long, press fit. Built with 26 AWG Spaced Kanthal coils and Rayon wicks with only one trimmed tail going down.
4mm outside and 3mm inside diameter, 10.5 mm long, press fit. Built with 26 AWG Spaced Kanthal coils and Rayon wicks with only one trimmed tail going down.
Last edited:
Was thinking bout that.. Nice work.I decided to modify my Lancia 1:1 clone from FC by replacing the Air Tubes with longer ones that I made from 304 Stainless Steel.
4mm outside and 3mm inside diameter, 10.5 mm long, press fit. Built with 26 AWG Spaced Kanthal coils and Rayon wicks with only one trimmed tail going down.
The Giraffe
I'm guessing the result is less leaking and more juice capacity?
Because those are the only things about the Lancia that give me grief.
But the leaking is my own fault as I tend to overdrip.
Because those are the only things about the Lancia that give me grief.
But the leaking is my own fault as I tend to overdrip.
a little untidy but it works, i was in a rush to make 4 new atty's up that i received today, poseidon-II,Holy grail(doge), dark horse and this lancia...
3/32 5wrap 24g 0.2Ω , nice warm flavoursome vape, really like it
3/32 5wrap 24g 0.2Ω , nice warm flavoursome vape, really like it
a little untidy but it works, i was in a rush to make 4 new atty's up that i received today, poseidon-II,Holy grail(doge), dark horse and this lancia...
3/32 5wrap 24g 0.2Ω , nice warm flavoursome vape, really like it
Little advice: I put small O-Rings around those dummy plugs because mine ware leaking.
I drilled the Airflow of this Pride too. (Both vertical tubes and horizontal holes are 2.5 mm now)
Built with 24 AWG spaced coil and single trimmed tail Rayon at 0.24Ω
Built with 24 AWG spaced coil and single trimmed tail Rayon at 0.24Ω
I'm guessing the result is less leaking and more juice capacity?
Because those are the only things about the Lancia that give me grief.
But the leaking is my own fault as I tend to overdrip.
No, if I don't tip it over LOL
Will do buddy..Did you twist a big o-ring to make it smaller or have you got some the same size as the plugs? i'm not sure which atty it came with but i had a small o-ring come which may fit, its quite thick and there was only one :/ but i been lucky so far
Will do buddy..Did you twist a big o-ring to make it smaller or have you got some the same size as the plugs? i'm not sure which atty it came with but i had a small o-ring come which may fit, its quite thick and there was only one :/ but i been lucky so far
I used little silicon fill port screws O-Rings from Fogger V4
Hey folks, I haven't posted a build for a while. I've gone away from the super subohm for this build as things were getting a little hot in here!
This little bad boy is sitting at 0.3ohm in my 28.5mm plumeveil on my hades. 26ga NiChrome, 1.8mm mandrel, 6/7 wraps spaced coils (spaced manually so they're a little uneven)
Vapes great, doesn't burn through juice like most of my super subohm builds and gives much better flavor
And yes, I did drop my mod and the top cap fell off the plumeveil and it dented the top of the chimney... a little annoying but it doesn't affect anything. Damn copper and it's super dentiness
This little bad boy is sitting at 0.3ohm in my 28.5mm plumeveil on my hades. 26ga NiChrome, 1.8mm mandrel, 6/7 wraps spaced coils (spaced manually so they're a little uneven)
Vapes great, doesn't burn through juice like most of my super subohm builds and gives much better flavor
And yes, I did drop my mod and the top cap fell off the plumeveil and it dented the top of the chimney... a little annoying but it doesn't affect anything. Damn copper and it's super dentiness
I hear you. 10-4
I'm an OTR truck driver too 48 States.
Here is what my truck looks like when I'm on the road:
AMD you have a ton of devices! I'm really curious to what are your favorite RDA and RTAs and why? I'd love to hear from someone that has pretty much every big thing on the market.
Do you prefer mouth to lung or lung inhales?
- Status
Similar threads
