Shinyitis Support Group

[icepickmaker84]

Happy Birthday!

Thank you!

 

[Opinionated]

Thank you!

Happy birthday!

So how many watts does that hoodie do?

haha

hope you have the best birthday ever!

 

[icepickmaker84]

Happy birthday!

So how many watts does that hoodie do?

haha

hope you have the best birthday ever!

Thank you! It’s powered by rubber chickens and I’m not sure where those work into Ohm’s law lol!!

 

[Fredman1]

PTFE sheet may well work for that issue.

Yeah I thought of that. I made a paper shim that works, but would rather get the purpose made ones in different sizes...if that exists.

 

[Eskie]

Happy Birthday @icepickmaker84

Thank you! It’s powered by rubber chickens and I’m not sure where those work into Ohm’s law lol!!

Check Steam Engine. They seem to have a calculator for everything.

 

[icepickmaker84]

Happy Birthday @icepickmaker84



Check Steam Engine. They seem to have a calculator for everything.

Thank you! Lol I’ll see if there’s a conversion. What I’m really starting to wonder is which mod maker can take the logo on the hoodie and put it on a mod.

 

[Hightech Redneck]

Yeah I thought of that. I made a paper shim that works, but would rather get the purpose made ones in different sizes...if that exists.

Get a hobby knife and trace your rda on a 2 liter soda bottle. Thin plastic to protect mods and several would change the airflow orientation.
I always said i was gonna try something like a 3/4 hole saw but never did.

 

[Eskie]

Thank you! Lol I’ll see if there’s a conversion. What I’m really starting to wonder is which mod maker can take the logo on the hoodie and put it on a mod.

There are a few custom builders out there who will do custom art for you. A cheaper path might be someone like J Wraps (or one of those wrap vendors) who can do an individual specialty wrap with your artwork. It's still an expense, but cheaper than a whole mod if you don't mind a wrap

 

[Tralfaz]

Hey shinies <3 Got my new cosmos today.

Fresh pair of Ni80 tri-core fused claptons.

The flavor on this atty is outstanding. It has everything I loved about the original with no twisty leads thanks to the re-oriented grub screws. I've been chain vaping the heck out of it and the cap is staying cool just like the original CSMNT. I'm pretty sure it's destined to become my favorite dual coil RDA.

 

[Fredman1]

Get a hobby knife and trace your rda on a 2 liter soda bottle. Thin plastic to protect mods and several would change the airflow orientation.
I always said i was gonna try something like a 3/4 hole saw but never did.

Whatever is used, it needs to be as thin as possible so as to control the orientation of the holes. At the moment one paper isn't enough..two is better, but three is to much again.
I really wonder if dedicated shims for RDAs has been made for the vaping market yet?

 

[Zazie]

How do you like the Gate RTA? Ive got a few in a cart, I dont know whether to hit the buy now button

I wish I could tell you. It's one of many, many I haven't tried out yet.

 

[Fredman1]

It's one of many, many I haven't tried out yet.

Seems you have the same problem as @charlie1465 ....way to much stuff

 

[Zazie]

I hope you are having a wonderful birthday, @icepickmaker84.

 

[Mordacai]

@Fredman1, it all depends upon the orientation of the thread on the 510.

But at least PTFE sheet is cheap, easily worked, is waterproof, compresses slightly and stops your mod getting scratched up.

The most you need is a hole punch to create a hole for the 510, then use sharp scissors or a knife to trim. Simples.

 

[Hightech Redneck]

Whatever is used, it needs to be as thin as possible so as to control the orientation of the holes. At the moment one paper isn't enough..two is better, but three is to much again.
I really wonder if dedicated shims for RDAs has been made for the vaping market yet?

Yes, there are some out there but they were not terribly popular so most shops dont carry them.

 

[Zazie]

Seems you have the same problem as @charlie1465 ....way to much stuff

Plus I get stuck in ruts very easily: once I've got a setup going, I tend to stick with it.

I also feel sorry for mods/attys when I pull them from the rotation. I need to start telling myself that they probably enjoy the break.

 

[Hightech Redneck]

Whatever is used, it needs to be as thin as possible so as to control the orientation of the holes. At the moment one paper isn't enough..two is better, but three is to much again.
I really wonder if dedicated shims for RDAs has been made for the vaping market yet?

Knew i saw some recently, kidney puncher has some.
KP Mod Guard 5 Pack- Various Sizes

 

[icepickmaker84]

I hope you are having a wonderful birthday, @icepickmaker84.

Thanks you!

 

[AngeNZ]

Whatever is used, it needs to be as thin as possible so as to control the orientation of the holes. At the moment one paper isn't enough..two is better, but three is to much again.
I really wonder if dedicated shims for RDAs has been made for the vaping market yet?

There's these:
$2.47 Replacement PC Heat Insulation Gasket for Atomizers (5-Pack) 5-pack - for 22mm diameter atomizer at FastTech - Worldwide Free Shipping

 

[AngeNZ]

And since you guys have sent me down the flat wire rabbit hole - is there some site which converts the metric measurements into the equivalent round wire gauge?

I know 28ga round wire is 0.3mm but no idea what the corresponding wire in flat stuff would be, apart from flatter