Shinyitis Support Group

[TrollDragon]

@Coastal Cowboy thanks for mentioning arctic fox firmware in one of your posts somewhere. Been playing with it on my pico
Now have a clock, a custom logo and having wàaaaaaaaay too much fun
Cheers

ArcticFox is awesome firmware but the clock doesn't keep accurate time on mods that don't have a clock chip.

You can adjust it so it's close and I think there are instructions in the Pico thread, but I can't locate them at the moment.

 

[TrollDragon]

That’s what drill presses are for, no???

No, that's what different atties are for.

 

[jfcooley]

Truthfully I don't like it.
The sticker is too thick and it shows, and I need to do some trimming.
Would have looked better had the background been clear.
May investigate something better. Went ahead and did it since I bought it and all.

Anyway...here ya go.

 

[NolaMel]

No, that's what different atties are for.

... haven’t done it in ages (before subohm caught hold), and definitely not on an rta, but I have been guilty of clamping down a tank and making it a TAD airier. I wouldn’t recommend doing it with a drill or dremel. Definitely a recipe for disaster

 

[NolaMel]

Truthfully I don't like it.
The sticker is too thick and it shows, and I need to do some trimming.
Would have looked better had the background been clear.
May investigate something better. Went ahead and did it since I bought it and all.

Anyway...here ya go.View attachment 738095 View attachment 738097

Scan it into your computer and print on clear contact paper

 

[jfcooley]

Scan it into your computer and print on clear contact paper

Not a bad idea.

 

[NolaMel]

Not a bad idea.

I’ve used a program called Print Shop for years. You could resize it with that too. That would let you cover the whole panel and trim off the excess

 

[untar]

Not a bad idea

Or send your mod/doors to a company that does laser burning (only advisable if the plastic is thermoset).

 

[untar]

Are those graphics in a vector or pixel format?

 

[TrollDragon]

... haven’t done it in ages (before subohm caught hold), and definitely not on an rta, but I have been guilty of clamping down a tank and making it a TAD airier. I wouldn’t recommend doing it with a drill or dremel. Definitely a recipe for disaster

As did I back in the day (the upper hole of the Sat22 just a smidgen), but there were no other options back then.

Nothing finer than a Dremel bit that has chattered across an atty. #ThatWillBuffOut

 

[TrollDragon]

Or send your mod/doors to a company that does laser burning (only advisable if the plastic is thermoset).

Hand Engraving.

 

[JamesDMad]

Don't drill it out though unless you have the necessary tools and at least some experience, you'll either injure yourself or destroy the device in the the process.

The Berserker is known to have a very tight draw since shortly after release, don't know why you would get one if you're not into that. If it was me I'd sell it to someone looking for a tight draw.

Lets just say some peoples idea of a restricted AF are much different than others. The flavor on the thing is fantastic. But when i draw so hard that my head caves in a bit and eyes pull back into my skull... That IMO is just a bit much..

I have done MTL in the past but more of a DL.. It's sure tough to beat the flavor on the little guy. switched out the nib tip with a different 510 and its more to my liking but still quite restricted... I have fun with it as it's quite unique and i appreciate change now and then.

Would never modify an Atty just to increase airflow on it.. I just wouldn't use as much if its not to my liking..

 

[Sickbxy]

I always thought that orchids were hard to take care of? Someone gave my husband one on his bus the other night, so I now have to try to NOT kill it.

@NolaMel , so how does one 'neglect' it just enough that it doesn't begin coughing up dust & wilting?

I lease orchids, I keep them while they are in bloom and swap out when the flowers fall off. Same concept that fancy office lobbies, doctor offices, etc do. I just need to keep them alive until they get swapped out.

 

[Coastal Cowboy]

@Coastal Cowboy thanks for mentioning arctic fox firmware in one of your posts somewhere. Been playing with it on my pico
Now have a clock, a custom logo and having wàaaaaaaaay too much fun
Cheers

It's a game changer for mods that use the Joyetech chipset. If you're a little OCD (like me) and enjoy tinkering and tweaking things until they're just ahhhh (like me), it's vaping nirvana.

 

[DeloresRose]

Don't drill it out though unless you have the necessary tools and at least some experience, you'll either injure yourself or destroy the device in the the process.

The Berserker is known to have a very tight draw since shortly after release, don't know why you would get one if you're not into that. If it was me I'd sell it to someone looking for a tight draw.

Well, because there’s right, and then there’s really, really, really tight, like five times tighter than any tank I’ve ever used.

So yes I was looking for mtl, but never expected this. You can read reviews till the cows come home, but some things are subjective, and you don’t know until you try.

 

[Coastal Cowboy]

I lease orchids, I keep them while they are in bloom and swap out when the flowers fall off. Same concept that fancy office lobbies, doctor offices, etc do. I just need to keep them alive until they get swapped out.
View attachment 738107
View attachment 738103
View attachment 738105

+1 for Chuck Norris.

 

[Fidola13]

So disappointed today. I got a Notification that I was getting a delivery today. I thought it would be the Paranormal and stuff but nooooooo
It was kitty litter & dog food !! Seriously ?

 

[NolaMel]

+1 for Chuck Norris.

And for knowing where the coffee/dessert spoon goes above the plate. I’m going assume the image is reversed since the silverware is flipped

 

[JamesDMad]

Has anyone ordered and received a device using the DNA250C as of yet?

 

[Fidola13]

Has anyone ordered and received a device using the DNA250C as of yet?

I have ordered the Paranormal 250C should be delivered Friday.