I get it. It was a heated convo but the name calling...been there, done that but we should refrain right?
Calling someone a "petulant child" who you disagree with displays a sound level of immaturity. 
Thinking you know it all with computer systems is true ignorance. Quite laughable actually.
Thinking you know it all with computer systems is true ignorance. Quite laughable actually.
I had a ][+ and a //e before I switched over to Commodore. I loved running EDD (Esential Disk Duplicator) on the old Shugart SA400s with speed controls, you knew the copy was going to be good once you heard that click from the drive.
I spent way too many hours in the Ultima Series.
They have always been confrontational and arrogant, I think that they can handle it @chanelvaps.
After all, this is a forum and we're here to discuss and not lecture.
After all, this is a forum and we're here to discuss and not lecture.
Someone let me know when they decide who's is bigger.
Oh man, the nostalgias and feels are strong right nowI had a ][+ and a //e before I switched over to Commodore. I loved running EDD (Esential Disk Duplicator) on the old Shugart SA400s with speed controls, you knew the copy was going to be good once you heard that click from the drive.
I spent way too many hours in the Ultima Series.
Probably around $500 if you had the mail in certificate from it too.
What $1.5m worth of limited edition Apple hardware looks like
And that is putting it mildly.
That's about what I sold it for in the early 90s. I got $550 IIRC, so I don't feel bad at all. I had everything with it including the original boxes and documentation.
Once again you are getting personal, labeling and name calling just should not go on. It is then that it is no longer a discussion. Not on anyone's side here, you would be more understood if you did not resort to that.
My mom used to tell me "always act in a way that you will not be embarrassed of yourself a year later." (I cannot tell you the number of times this was HARD in life)
Last edited:
Does anyone know the size Philips head screws the Hussar v1 clone takes? This one:
$4.21 Hussar V1 Styled RDA Rebuildable Dripping Atomizer - stainless steel / 22mm diameter at FastTech - Worldwide Free Shipping
I measured but I don’t think I’m measuring it correcting. And also where to buy?
The heads on the included screws are a bit small I had the worst time this morning installing a coil. I tried GV ss316l Juggernauts, ss316l 24g & finally ss316l 26g. The head needs to be a little larger.
Big thanks in advance !
$4.21 Hussar V1 Styled RDA Rebuildable Dripping Atomizer - stainless steel / 22mm diameter at FastTech - Worldwide Free Shipping
I measured but I don’t think I’m measuring it correcting. And also where to buy?
The heads on the included screws are a bit small I had the worst time this morning installing a coil. I tried GV ss316l Juggernauts, ss316l 24g & finally ss316l 26g. The head needs to be a little larger.
Big thanks in advance !
No it's my Intel hard drive which is failing but it was over 10 years old now so I can't complain. I do have a seagate ext. drive and although their failure rate is worse than western digital it by no means is the case that either mine will or that you shouldn't buy one... Depends to some extent what use it will get
I just measured one with my digital caliper and the Hussar v1 RDA uses M2*4 phillips screws.
$1.92 Replacement Phillips Head Screws for Atomizers (50-Pack) - M2*4mm at FastTech - Worldwide Free Shipping
I'm sure they can be found elsewhere with some google fu.
Measure the length and diameter of the screw.
The deck design of the v1 won't allow for a screw with a larger head to be installed.
Thanks! Yes, I have a Brother PE800. It’s an entry level machine, but it does good work.
I got one towel done and realized I was on my last needle so I’m done till I get more.
Thank you! I knew you would know. I tried measuring but I don’t think I knew what I was doing lol!
Thank you! Thank you!
Similar threads
- Locked
