Sounds good but what if the red one is your favorite and you drop the red one on a concrete driveway and it's a gonner. The whole deal is having a complete set and suddenly you don't have a complete set anymore. Then you discover they are out of production. The time to act is now.
I've been having an annoying problem lately with Lemos. I use 2 Lemos and the wife has 6. She tends to chain vape and burn up anything that isn't TC. That's been working out fine for years but suddenly hers are giving me fits. They start out fine after a service, but then they randomly stop working. The screen shows everything is fine but when you hit them nothing happens. Take the bottom off the tank and reattach it and it works for a while but goes bad again. And the resistance creeps up from 0.75 to 80's or 90's.
Today I'm planning to break one down. Take apart the deck and everything else. Check all the silicone. Clean out the screw holes. Clean all the contacts on the Solos. Anything is possible though. Could even be a bit of bad SS wire on the spool. Haven't had to deal with problems like this for a while since I've been using the same gears for years.
Today I'm planning to break one down. Take apart the deck and everything else. Check all the silicone. Clean out the screw holes. Clean all the contacts on the Solos. Anything is possible though. Could even be a bit of bad SS wire on the spool. Haven't had to deal with problems like this for a while since I've been using the same gears for years.
What does the screen show at that time, i.e. when hitting?
Sometimes it shows all the normal stuff and when I press the button and it doesn't fire and nothing changes on the screen. Actually I really don't know because you can't see the screen while you take a hit. Guess I could try it with a mirror.
A lot of Lemo problems come from the deck screws getting loose. I always double check them when I put new coils or wicks in but it's just a Lemo thing. They can come loose over time, which would cause increasing resistance.
It's not all the Lemos either. I got a dodgy one that's due for a new coil so when I do that I'll try taking the deck apart and clean the Solo.
The wife drops them on the floor a lot.
You get good flavor off of the right boro. But it depends on how you vape. If you like the cloudier stuff you may not like it.
But imho it's hard to beat a good rda on a squonk. And yes they are not making nearly enough squonkers anymore.
My dailies are squonkers, and some are getting worn out. I'm gonna be in trouble in the not to near future lol.
Made some progress on my Lemo problem. Took one of my wife's Lemos that was acting up and did some swapping around. My Lemo worked fine on her Solo, hers didn't work on my Solo, so I knew it was the tank. Took it apart and one of the deck screws had come loose. Later she dropped one and it started misbehaving. I opened it up and the screws were OK, put in a new wick and it started working. There's one more that's dodgy, check that out tomorrow.
While I was doing that I cleaned out a couple of Solos with 99% alcohol. Used to do that regularly with mods but I got out of the habit. The battery terminals didn't look too bad but it doesn't take much to mess up the connection. The battery door threads were filthy. I'm keeping a list now so I can get all the mods cleaned up.
While I was doing that I cleaned out a couple of Solos with 99% alcohol. Used to do that regularly with mods but I got out of the habit. The battery terminals didn't look too bad but it doesn't take much to mess up the connection. The battery door threads were filthy. I'm keeping a list now so I can get all the mods cleaned up.
I couldn’t get any more of my favorite eliquid so I put away my equipment and decided to try again.
I use singe micro coil devices.
I’ve tried dual coil and they require too much air flow.
I prefer a restricted dl or loose mtl for max flavor.
I‘ll take a look and see if I can find one in stock.
So far out of stock.
If you're comfortable with a mech squonker, I could pif you an og VV Pulse still unwrappped.
Last edited:
Similar threads
- Locked
