Svoemesto Kayfun Mini V3

[stanleybb50]

I added a flow ring for the V3 and Provari P3 and it looks great except the V3 won't fire with the flow ring. Any suggestions?

View attachment 531614

If maybe you didn't take into account the 19.9 or 20mm bump out on the Mini v3 maybe?

Im gonna order a 22.7 - 19.9 flow ring myself. If it's tight, it's tight...

- Sent from my Note 5 via Tapatalk

 

[Impulso]

Ok, which way these are rotating Raitis? Clockwise or Anti-clockwise?
...
View attachment 531749

Rotating? That's all wrong. I see a floating provari v4. It's so obvious. Can't you see it? Pifft...

Edit - now I see a cat puffing away a 22mm kayfun v5?

Double edit - ignore above - I'm crazy


Sent from my iPhone using Tapatalk

 

[usr/]

This may be the last tank I ever need.....until the other one gets here. lol! Perfect right out of the box. My NET never tasted so good. What a piece of work! Now to get my hands on that Dicodes

 

[AstroTurf]

Now to get my hands on that Dicodes

Yes!!!

My Second should be here Tomorrow.

Jim

 

[TheotherSteveS]

Yes!!!

My Second should be here Tomorrow.

Jim

You are going to hate me but I noticed this yesterday and ordered one immediately. Not a site I was familiar with but all good and it will be sent out today..A ridiculous price really and without tax will be under $100..

Tiny

Paid £78 all in.

Anyway, no idea how many are left. There are some telegenos also for the same price. Hope someone can benefit anyway!
Any questions contact Ditta
info @ hadivape.nl

 

[TheotherSteveS]

Uptill now no, no such problems.
1. Pls keep it to 1.5 turns if using less than 70% VG
2. Even if on higher VG - after a while bring it back to 1.5 turns
3. Take slow, steady and smooth draws. Remember, with every pull you're also pulling in juice into the chamber.
4. I'm sure you're by now well versed with the amount of wicking material to use. So no comments on it.

Thanks stan, I'm pretty much doing all of that. I mean its a pretty simple device, gloriously so, so I'm a bit perplexed at what is going on. I may strip the whole thing down, clean it and start again, maybe change a few orings or something. I'm sure I can sort it out! Thanks for your help as always!!

 

[AstroTurf]

You are going to hate me but I noticed this yesterday and ordered one immediately. Not a site I was familiar with but all good and it will be sent out today..A ridiculous price really and without tax will be under $100..

Tiny

Paid £78 all in.

Anyway, no idea how many are left. There are some telegenos also for the same price. Hope someone can benefit anyway!
Any questions contact Ditta
info @ hadivape.nl

Great Post!!!

Great Price!!!

For a Great Lil Mod!!!

Thanks, Jim

PS The money to me, really matters not, Vaping Satisfaction Does!

 

[TheotherSteveS]

Misread...ignore me...

 

[AstroTurf]

Anybody having a problem with juice seemingky creeping into the air-flow path. Its not flooding per se, I get many hours of fine vaping and then for some reason a slight kinda wet, light gurgling thing kicks in. I thought initially it was because i dumped juice down the deck chimney but I have rewicked it four or five times with at least four different wicking materials (rayon, muji, bacon and cotton/rayon mix) now, high coil, low coil, and the same thing happens every time. More wick, less wick. Tried a few things. JF anywhere between 1.5 and 2 turns (the latter with 70VG). It vapes well, 1.2 ohm now at 14W, but this squeaky, gurgling thing always starts eventually. Now its often when the juice level is low. Possible one of the orings is a bit screwy and Im losing vacuum?? I'm a bit perplexed. I'm a klutz but I know how to build a bloody atty without these issues...apparently not with the V3...
Any ideas suggestions gratefully received cos I'm nearly out of them?!?!

Having thought about this...

I would tighten up the 5mm nut on the bottom of the tank.

Jim


Sent from my iPhone using Tapatalk

 

[raitizz]

Ok, which way these are rotating Raitis? Clockwise or Anti-clockwise?
...
View attachment 531749

Both, Q, just like my K4

R

Edit: ..and my head.

 

[Pinggolfer]

I ain't makin' any promises!
But that O-ring on the Provari flat cap is very stiff.

It was a no go HB. The Provi center pin doesn't come up much.

If maybe you didn't take into account the 19.9 or 20mm bump out on the Mini v3 maybe?

Im gonna order a 22.7 - 19.9 flow ring myself. If it's tight, it's tight...

- Sent from my Note 5 via Tapatalk

Stanley I ordered 19mm to 23mm. If you look at the bottom of your V3 you'll see the square piece which comes off when removing the 510 screw is recessed. This is where the problem is. My flow ring covers the entire round part of the base and turns smooth around the V3. Look at the two pictures below. There are not enough threads exposed to touch the 510 pin on my P3.

 

[AngiBe]

Neat.

Clear View mini
Steam Tuners

R

That looks super cool

 

[Pinggolfer]

Ping...
Circuit Board Spacer | Madvapes

Also available (probably for free) at your local computer repair joint.

Will the circuit board spacer screw up my other attys?

 

[Bronze]

That looks super cool

This KM3 is only 2ml capacity but is a killer atty.

 

[Bronze]

Pingy, I think the flange on the KM3 (where the air holes are) is riding on top of that flowring and not allowing you to screw down the KM3 all the way. The only way a flowring would work and look right on the KM3 is if the height were less than the height of the bottom-most tier of the atty. That flange out where the airholes are is a show stopper.

 

[Pinggolfer]

Pingy, I think the flange on the KM3 (where the air holes are) is riding on top of that flowring and not allowing you to screw down the KM3 all the way. The only way a flowring would work and look right on the KM3 is if the height were less than the height of the bottom-most tier of the atty. That flange out where the airholes are is a show stopper.

You confused me and that's a easy task. The flange doesn't come close to the air holes. The flange stops where the V3 gets wider just below the air holes.

 

[raitizz]

This KM3 is only 2ml capacity but is a killer atty.

I think this plastic tank holds a bit more. We'll know soon enough.

R

 

[subwayaznm]

Good morning everybody; make it a great day. & Vape on

The Kayfun v5 will be here sooner than we expect

 

[Bronze]

You confused me and that's a easy task. The flange doesn't come close to the air holes. The flange stops where the V3 gets wider just below the air holes.

That would be correct. When I say airholes, I am referring to that wider section on the KM3 where the airholes reside. That wider section is where your flowring bumps up on and prevents you from screwing your KM3 all the way down on your P3/Radius.

 

[kates]

@Pinggolfer Can't you take the outer ring off the provape and then put the flow ring in it's place. In the gap in this photo?

This thing is fantastic - couldn't resist and glad I didn't, my no spend in 2016 is officially over