How many cu ft is your fridge? Mostly wanna know so I can calculate your approximate weight and size.
I did both... and it's not a cheater answer as that's what I actually did.
I bought 3 of each make/model of all hardware and I bought a ton of different stuff, just in case there was a common problem with something. The only exceptions were my Hellbeasts and Solos, I got 6 of each of those and then one other mod that I bought 3 of that I forgot I had already bought 3 of a couple months earlier. This was for 2 people though. I am splitting things up into 3 boxes, 1 box will be kept at my home and 2 of the boxes will be kept at 2 different locations so I will be covered in the event of a hurricane, fire, burglary, etc..
EDIT: Oh, I forgot, I got 10 of the Triton mini tanks and 11 of the M17's.
Last edited:
Do your tanks not have adjustable airflow or something??resistance, 0.15 watts would be like sucking air from a straw.
One one of my orders the restocking goes out 15 days and on another on it goes up to as much as 24 days.
honestly at this point I wonder if my last 2 FT impulse buys from early Jan will get to the US before the May cutoff date. I wouldn't order anything from China at all from now on. I don't think I would trust that it would arrive before the US Government could start seizing stuff at customs in May.
Even if this virus was miraculously gone tomorrow this is going to take weeks to months to ramp up productions and shipping on the backside.
If you are not stocked now you need to grab what you can from US sellers before they run out of everything and you need to do it in hurry. That is my best advice.
Even if this virus was miraculously gone tomorrow this is going to take weeks to months to ramp up productions and shipping on the backside.
If you are not stocked now you need to grab what you can from US sellers before they run out of everything and you need to do it in hurry. That is my best advice.
Vaporl is shipping once again. Tracking shows my 1/30 order arrived at the shipper in the Netherlands. Perhaps they are working around the rules?
A note on this.
From information I found online previously, this mod is apparently only for tootle puffers (low power). The wiring and switch are apparently only built for about 3A use, which translates to 1.25 ohms or higher (think of it as 1.3 ohms and above).
5 Crappy mechanical mods I own, and 2 decent ones
(I also found a reference to the coil resistance in one of the older ads for it, but don't have that link at hand).
I like mech tubes with side switches, but for my use I went for the protected quasi-mech Ehpro Armor Prime. Those run around $21 from China resellers. The v1 takes 20700 batteries, while the v2 can also handle 21700. (I have 3 of the v2)
Read a few article about Chairman XI stressing that the economy needs to get back to normal.
Seems like the economy may supersede health?????
"Officials in the province of Zhejiang said yesterday that their focus has shifted from all-out efforts to prevent and control the outbreak toward containing the epidemic while ensuring the economy’s operation."
I've been rather spoiled lately trying out new tanks with gt, kanger Clapton, and zenith coils. I really need to switch back to my rtas and save the coils for later. I discovered that I really like my NETS in the zenith with a 1.2 coil but have also been running a zlide 4ml which is going to make me go through coils quicker. I think I'll dig back out more of my zeus and intake rtas.
Some people do. But I’ve never done it. I’ve been diy for 6 years and my nic is in the freezer, but my juice is in a cupboard. I don’t let the house get too warm, only have a window AC but the cabinet is in a cooler area, never more than 75F.
Some of my liquids have been 4-5 years old and have been just fine
I think it’s a personal preference, and whether you have fridge space.
For me, it’s about what resistance works best in the atty and what atty best compliments the mod I want to use.
For mechs, I like to stay around .3-.4 single coil, but some mechs are kits with a dual coil so I have to account for that. More complicated.
For regulated mods, I don’t have to think about that, it’s all down to whatever works best in the atty without being too hot or not enough vapor.
Same here
I have two squonkers loaded with my ADV and diy lemon cream, but have kept a couple of tanks out for use with some commercial eliquids. I ought to get off my tail and build a couple of RTAs (maybe try the sxk Haku riviera rdta).
I continue really liking the Skullkandy Alchemist mech squonker that I picked up last year, before starting on stocking up. It's a 3d printed 21700, modmaker silver contacts and connector. Easy maintenance, consistent performance, made in PA.
I'm lazy, if a kit comes with a dual coil topper it goes in the pif pile, and I put on a single coil rda/rta [emoji3]
I've been building 2.5mm id twisted 26 kanthal for several years, just recently switched to 3mm for several rda/rta. 1 less wrap compared to what I'd build at 2.5mm cuts the resistance a bit. Everything I build is .35 - .4 ohms now.
in' creepy! 
IIRC, what he talked about was that he'd tried coils that were 0.15 ohms and 0.18 ohms. He wasn't talking about wattage.
lmao... I did not even catch that it said watts, I just saw the number and my mind switched automatically to ohms.
Question/Poll...
When do most of you say enough is enough for your batteries? Like right now I have an 18650 that only lasts about 4 hours, which is really super annoying, but I am having trouble letting go because I want to get every last drop out of it. lol
@UncleJunkle touched on this in a previous post which I cannot find...
When do most of you say enough is enough for your batteries? Like right now I have an 18650 that only lasts about 4 hours, which is really super annoying, but I am having trouble letting go because I want to get every last drop out of it. lol
@UncleJunkle touched on this in a previous post which I cannot find...
Similar threads
