AVAILABLE NOW - SMOKtech TT Terminator Tank Rebuildable Dripping Atomizer and/or Tank Fed Atomizer System; Available For a Very SPECIAL Price! VIDEO W

[BadDaddy4007]

I've had my TT installed in a AGT and loved it. I had no problem with wobbles, juice flow or anything else.
Until I blew out my coil and started to rebuild it. My mistake though, I had switched devices and forgot to lower the wattage. SO no big deal, I thought. I can't get the center pin out of the ceramic cup. Tried pulling, twisting (hoping not to break the cup) to no avail.
Any one have any ideas or tips on how to do that? I really like the way this performs and want to get back to happy vaping on it.

 

[djtonyb]

Now im confused,, so i misunderstood "TEACH" but he told me the the 510 adapter needs to be very tight and open and close the other threading, and that do make sense to me also because in the bubble threading also have a hole...

I use the TT all day today with the 510 very tifgt to adapter and opening/closing the booble threading and did works perfect,,

So like "chapulin" "y ahora quien podra defenderme"



Sent from my iVap using Tapatalk HD

If it works, great! My understanding was that the upper threads are meant to be closed, because they keep the negative coil connection pressed against the outside of the chamber, and you only unscrew it to access the coil for cleaning and rebuilding. The same discussion happened in a killer thread, and that's how I figured out that the 510-510 could actually be unscrewed... it was so tight I thought that the only opening was the bulb, and it wasn't working right for me.

 

[djtonyb]

I've had my TT installed in a AGT and loved it. I had no problem with wobbles, juice flow or anything else.
Until I blew out my coil and started to rebuild it. My mistake though, I had switched devices and forgot to lower the wattage. SO no big deal, I thought. I can't get the center pin out of the ceramic cup. Tried pulling, twisting (hoping not to break the cup) to no avail.
Any one have any ideas or tips on how to do that? I really like the way this performs and want to get back to happy vaping on it.

This is just hearsay, as I haven't tried to rebuild mine yet, but I read on another thread (either the killer or a terminator thread) that someone who's cup was stuck pulled out the pin from the bottom rather than trying to pull the cup upwards.

 

[Adrena]

never mind

 

[djtonyb]

Also, has anyone noticed these things drink juice at a pretty rapid rate? I lowered my nic from 12mg to 6mg because these blast through 3ml in a few hours, as opposed to my Protanks that will last me the better part of an entire day. I didn't sleep well all weekend because I vape a lot before going to bed.

 

[rdsok]

The amount of vapor produced is directly proportional the amount of e-liquid that is consumed ( unless there is a leak of course... lol ). The more e-liquid that is used, the more vapor that is produced.

 

[BadDaddy4007]

This is just hearsay, as I haven't tried to rebuild mine yet, but I read on another thread (either the killer or a terminator thread) that someone who's cup was stuck pulled out the pin from the bottom rather than trying to pull the cup upwards.

Tried that and I did get it out. But getting that little sucker in with the non=resistance wire was a bear. So now I have to find another ceramic cup to fit or just by more TT. Not sure how this is going to work, as I like having devices that I can rebuild to my liking.

 

[DaxFX]

Also, has anyone noticed these things drink juice at a pretty rapid rate? I lowered my nic from 12mg to 6mg because these blast through 3ml in a few hours, as opposed to my Protanks that will last me the better part of an entire day. I didn't sleep well all weekend because I vape a lot before going to bed.

In fact mine is the other way comparing to my protanks. I filled up yesturda morning and today at this moment still 1/2 tank, i have a couple of tanks and clearo wich i switch during the day, but usually at this same rate my protanks would be almost empty..

Since yesturday im starting to like this thing more and more , is cheapy wobly thing but just vape awesome, im thinking on geting the AGR to hold it better, and use the tank for my cartos, and as a dripper is just a pure clean vape i loved also as a dripper. This thing could be improved into a version 2 with pyrex glass and maybe a reverse threading for open the juice feeder without unscrew the the complete setup. Or any loking system.

Im on the waiting list for version 2.


Sent from my iVap using Tapatalk HD

 

[Vap Khymyst]

Tried that and I did get it out. But getting that little sucker in with the non=resistance wire was a bear. So now I have to find another ceramic cup to fit or just by more TT. Not sure how this is going to work, as I like having devices that I can rebuild to my liking.

The cups from some CE2's that I bought in a co-op 2 years ago fit and work well. Don't know about the current versions though!

 

[BadDaddy4007]

The cups from some CE2's that I bought in a co-op 2 years ago fit and work well. Don't know about the current versions though!

Well, it's worth a shot then, thanks for the info.
I really like this set-up, I can adjust the air flow, amount of juice going to the wick, not to mention I can use it in all the empty tanks that I have.

 

[djtonyb]

The amount of vapor produced is directly proportional the amount of e-liquid that is consumed ( unless there is a leak of course... lol ). The more e-liquid that is used, the more vapor that is produced.

Thing is, the vapor didn't seem a whole lot thicker, but the flavor was much better than the Protanks... I've actually got to do some real volume comparisons, as a am guesstimating the amount of juice consumed, not measuring it out to the .01 ml. From just a quick glance, it seems that the AGR with the long tank and the Protank would hold close to the same amount of actual vapeable juice before I would refill them. Cylindrical displacement physics with the tanks refractive distortion is hard to eyeball...

 

[VapingTurtle]

... Cylindrical displacement physics with the tanks refractive distortion is hard to eyeball...

Please don't forget to factor in the conformative deformation of the hyperbolic incongruity.

 

[DaxFX]

Chanfle !!!


Sent from my iVap using Tapatalk HD

 

[Asmuth]

I've been using this thing for a week and haven't had to rebuild yet, but I'm impressed so far. The included tank is junk, it wobbles real bad on my PV, so I put it in an AGR and it much better. They should offer this without the tank and drip tip to make it cheaper or replace that stuff with extra heads, or replace the stock tank with the AGR and charge a little more.

Anyway, I have a question, has anyone drilled out the feed hole or added a second feed hole? I have it wide open and still get burnt hits every once and a while, it just doesn't feed fast enough for me. I usually go through a tank every day, but I'm a day and a half on this tank and still have about 1/4 a tank in there. Just wanted to see if I was the only one with this problem.

 

[djtonyb]

I've been using this thing for a week and haven't had to rebuild yet, but I'm impressed so far. The included tank is junk, it wobbles real bad on my PV, so I put it in an AGR and it much better. They should offer this without the tank and drip tip to make it cheaper or replace that stuff with extra heads, or replace the stock tank with the AGR and charge a little more.

Anyway, I have a question, has anyone drilled out the feed hole or added a second feed hole? I have it wide open and still get burnt hits every once and a while, it just doesn't feed fast enough for me. I usually go through a tank every day, but I'm a day and a half on this tank and still have about 1/4 a tank in there. Just wanted to see if I was the only one with this problem.

Screw the bulb tightly down and loosen just the bottom 510-510 connector... that is where it was designed to feed... the hole in the bulb is where the negative end of your coil makes contact. There are 2 feed holes in that lower connection that are adjusted by screwing the whole top assembly, including the whole bulb, up. You can see in this photo the bulb is screwed closed, and the feed holes are underneath the bulb in the gap.

 

[WallyO]

Screw the bulb tightly down and loosen just the bottom 510-510 connector... that is where it was designed to feed... the hole in the bulb is where the negative end of your coil makes contact. There are 2 feed holes in that lower connection that are adjusted by screwing the whole top assembly, including the whole bulb, up. You can see in this photo the bulb is screwed closed, and the feed holes are underneath the bulb in the gap.

Now THAT makes sense. I thought the upper portion was the feed adjustment. Doh!
How's it workin for you djtonyb??

 

[djtonyb]

Very nice, although it takes a bit of fiddling to get right. Every once in a while I have to screw the assembly all the way down, then back up again a couple of times to get a few bubbles out. The flavor is pretty darn good, though! I still love my protanks, but the TT has been my all-day go to since last Friday. I ordered a few ceramic cups for it so I can pre build a few coils in advance. I still have yet to use a real carto in a tank, so I can't say how they compare.

 

[DaxFX]

Same here, at first i didnt liked, but the flavor i was getting was so good that i just keep trying it, now im using every day, i have several mods for switching during day and my TT is full of juices in one of them

I still hate the wobling but an AGR is my wish list.


Sent from my iPhone using Tapatalk

 

[Adrena]

Screw the bulb tightly down and loosen just the bottom 510-510 connector... that is where it was designed to feed... the hole in the bulb is where the negative end of your coil makes contact. There are 2 feed holes in that lower connection that are adjusted by screwing the whole top assembly, including the whole bulb, up. You can see in this photo the bulb is screwed closed, and the feed holes are underneath the bulb in the gap.

OK wait that low lower bit is not unscrewing for me just the bulb.
I have totally mangled my addy piece now.... I was in the right track when I said my never mind.....

 

[VapingTurtle]

OK wait that low lower bit is not unscrewing for me just the bulb.
I have totally mangled my addy piece now.... I was in the right track when I said my never mind.....

That is the 510-510 adapter junction with the lower half of the atty.