iTaste MVP v2 Owners Group

Status
Not open for further replies.

Vermiform

Super Member
ECF Veteran
Verified Member
Apr 18, 2014
530
1,615
Louisiana
You can use this coil calculator to estimate what a coil is going to be. Always check it with a multimeter after you make the coil. Make two coils as identical as possible of 3.0 or higher. Two 3.0 will be 1.5 on the device. That will work fine on the MVP but the battery will run down faster than a single coil.

Coil wrapping | Steam Engine | free vaping calculators

Awesome calculator, thanks! I have an ohm meter and my last dual coil came out to .96 so I have been using it on a cheap mechanical clone. It's "ok" but no wow factor yet. I'm still learning.......
 

Stierwalt3

Senior Member
ECF Veteran
Verified Member
Apr 8, 2014
210
294
Everett,WA
your gonna need 2 atty's, your Nemi will run great between .6 & .8

...on the MVP i wouldn't go under 1.3 and you'll be maxed... and smaller RDA's like the Nimbus work perfect on it.

28ga kanthal dual coil-7 wraps on a 1/8th bit should give ya about 0.75
28ga kanthal single coil- 10 wraps on a 3/32 bit should put ya around 1.3 or so
heat & pinch tight and wick w/cotton

another great dripper, good clouds and taste
https://88evape.com/shop/rebuildable-atomizers-tanks/apo-rda-atomizer-clone/?age-verified=0e5a6d5181
sando7-albums-mec-s-picture343559-apo2-apo-clone-taken-apart.jpg
[/IMG]

sando7-albums-mec-s-picture343560-apo1-apo-copper-clone-accessories.jpg


the APO RDA, perfect for the Nemi - comes in brass or copper w/drip-tip & accessories ..w/two sets of dual cyclops holes (for dual coil)..... and one single hole (1 coil)

That's a tough one. I'd say you want to hit 1.5ohm. Anything above that wont be particularly satisfying on a mech mod and the MVP will still produce about 3.9V with a 1.5ohm coil. 1.5ohm would probably be about 6-7 hand wraps on doubled 2mm silica give or take.

If you are going to use cotton and double vertical micro coils, you'd need to get Two coils of 3ohm each. Remember double coils fire at half the resistance of single coils.

You gentlemen are too kind, thanks for taking the time to supply so much info!

i can wrap an 0.76 in my sleep...i wrap then check-um and rite on the money...from repetition!


I got a 1.3 down :D
 

sando7

Ultra Member
ECF Veteran
Verified Member
Feb 8, 2014
2,308
2,390
Louisville, KY (PRP)
no not much diff on that....if you like it go for it....what i noticed when i went to low 0.4 & .5 after dripping for awhile and then hitting the sack when i got up in the morn my throat felt like i slept rite under the ac, sorta burning sensation when taking a breath....jumped up to .7 or so and it's not bothering me anymore...i also quit taking giant lung hits all the time...just a good toot and i'm good to go...jmo

i'm gonna call it a night, have a good-un
 
Last edited:
now if innokin got there heads together and made and MVP 3 with a dna 30 chip id be so all over that.
ive seen an MVP converted to DNA30 ( though they never switched the batteries so couldnt fire above around 12 watts which seems a bit of a waste of time ) but its def something that i would buy if done peoperly.
 

herb

Vaping Master
ECF Veteran
Mar 21, 2014
4,850
6,723
Northern NJ native , Coastal NC now.

Midniteoyl

Vaping Master
ECF Veteran
Verified Member
Apr 19, 2014
3,769
4,882
Indiana
made a slo-tek order yesterday for a kf mini went and checked the site today and it said will be shipped out on the 13th, so 6 days just to get out the door....man they must take millions of orders...also paid for the usps shipping option, whatever that is?

China post directly to USPS.. usually the fastest option. Takes as little as 8 days if it makes it through customs quickly.
 

sando7

Ultra Member
ECF Veteran
Verified Member
Feb 8, 2014
2,308
2,390
Louisville, KY (PRP)
I am thinking I am missing a piece to fit my nimbus that is coming.....what is the black piece in between your RDA and your MVP?

Sent from over here.

actually there are 2 pieces there underneath the Nimbus, the top piece is an airflow control adapter and underneath is the MVP beauty ring; i spray-painted both blk.
 

vanillayo

Super Member
ECF Veteran
Verified Member
Jun 14, 2011
315
227
South Carolina
i just grab another mod off the table and have at-it :)

rite now i have 4 rda's, 2 rba's and 2 tanks w/different builds/joozes all on diff mods and a goin at it :vapor:

just put a carto tank full of honey-suckle on the MVP, man it tastes goooood

Where did you get the honeysuckle? I'm looking for a good one.
 

pufZeppelin

Vaping Master
ECF Veteran
Jul 6, 2013
7,610
24,603
Florida, SW
I am thinking I am missing a piece to fit my nimbus that is coming.....
what is the black piece in between your RDA and your MVP?

sando did some custom black painting
but it's the MVP beauty ring (obviously) and above it is one of these...
- Tank Airflow Controller





sure is a nice sunny day....

:)
 
Last edited:

sando7

Ultra Member
ECF Veteran
Verified Member
Feb 8, 2014
2,308
2,390
Louisville, KY (PRP)
Where did you get the honeysuckle? I'm looking for a good one.

had to make my own, got the flavor at Vices..if you want the link just hollar and i'll PM it to ya, never mind...link just sent via PM



edit:
i'm amazed at how good a Carto Tank works with the MVP and the taste is wonderfull; yall gotta try one!
 
Last edited:

AG51

ECF Guru
ECF Veteran
Jan 23, 2011
82,919
390,399
Dat Way →
Hello
greetings10.gif
I had never stopped to read this thread but this morning I did some of it. What a wonderful helpful bunch of people :) I too am an MVP2 lover and have a few of them. I'm a basic keep it simple vaper and use my MVP's with my mini Protanks mostly. Great vape for me. I need to go back and read this whole thread. :D A friend of mine had given me some leather and I went to work sewing myself some lanyards for my MVP's. This is what I came up with (artwork painted by myself). Great for working out in the yard :laugh: I don't sell these and I'm not a supplier, just wanted to show my love for the MVP to others who feel the same. I have given some away to people in the past and had a contest for a couple not long ago. Now I go back to reading some more :laugh: Have a great day !
MVPLanyards_zps368c3921.jpg
 
Status
Not open for further replies.

Users who are viewing this thread