iTaste MVP v2 Owners Group

[garyoa1]

Someone on a thread I posted in General suggested boiling. I poked the air holes on the sides of the nut (?) on the bottom of the tank.

Yup. That was me (among many others). The idea is to melt any gunk that's inside small channels that you can't reach. I'm surprised you had to poke anything after 10 minutes.
I wouldn't boil the plastic or glass tanks since they're easy to clean but it shouldn't hurt them.

 

[Keirster]

that is weird, but all it could be is the positive block and or the coil making contact
of the nano kit (due to fact other works fine)
should be able to detect without assembling and filling
just put chimney ‘chamber’ on, test fire
then add chimney top, test fire – I said ‘coil’ thinking maybe you have a
nice big vertical coil built which is as tall as chimney cap
you think if a bad fit, you would notice it as assembling
keep us informed, curious about this…

I will try again tonight and see if I can figure it out, Thanx Puff.

 

[kojul]

I have never seen a long green light on MVP before. input the standard parts back on and it works fine.

I've only seen that long light once and that's when I tried to fire a coil that was around 0.7 Ohms and I immediately pulled the atty off because I was afraid of damaging my MVP. Anyone else know what this long green light actually means?

 

[sando7]

it means there is a short

 

[Midniteoyl]

Yep.. ohms too low/short

 

[herb]

Hey Puff, what do you think of this , gets great reviews. I can't find a nimbus on the site though.


http://www.fasttech.com/products/0/10005661/1442201-mt3s-bcc-bottom-coil-clearomizer-3-0ml

 

[Midniteoyl]

I have some of those... http://www.e-cigarette-forum.com/forum/clearomizers/567056-dual-coils-t3s-mt3s-maybe.html

Rewicked with cotton and those generic dual coils, they taste great and last a long time with NETs before clogging.

 

[Shadav]

Hey Puff, what do you think of this , gets great reviews. I can't find a nimbus on the site though.


$3.49 MT3S BCC Bottom Coil Clearomizer (3.0mL) - silver / 2.2-2.6ohm at FastTech - Worldwide Free Shipping

that's not a dripper...it's more like an evod tank...
Eternity Rebuildable Atomizer is the vision ET clone that I use and you can buy premade coils if you don't want to make your own Pre-made Wires and Wicks for Atomizer (50-Pack)

 

[pufZeppelin]

Hey Puff, what do you think of this , gets great reviews. I can't find a nimbus on the site though.


$3.49 MT3S BCC Bottom Coil Clearomizer (3.0mL) - silver / 2.2-2.6ohm at FastTech - Worldwide Free Shipping

I have ONE of those, and it seems to work as good as my real Kanger T3S
- $3.49 MT3S BCC Bottom Coil Clearomizer (3.0mL) - silver / 2.2-2.6ohm at FastTech - Worldwide Free Shipping

but have about a dozen of these
- $2.93 T3S BCC Bottom Coil Clearomizer - translucent / 2.4ml / 1.5ohm at FastTech - Worldwide Free Shipping
the metal band that is friction fit to tank is delicate (in wifes pocket )
but for me, work great, one of my fav’s (holds 3.0 ml contrary to specs)
guess I just like ‘looking’ at the inside goings on

right now I am playing with one of these
- $3.32 RGM2 Bottom Coil Clearomizer (2.0mL) - glass tank / 2.2ohm at FastTech - Worldwide Free Shipping
and I put the base from this on it...
- $2.20 GS-H3 Bottom Coil Clearomizer (2.0mL) - smoke black / 2.4ohm at FastTech - Worldwide Free Shipping
and now it looks like I have a mini MT3S-Glass

- - -
is this what you seek ?

- $6.22 V5 RDA Rebuildable Dripping Atomizer - 1*airhole / laser etched logo / 1.8ohm at FastTech - Worldwide Free Shipping
- $4.97 V5 RDA Rebuildable Dripping Atomizer - 1*airhole / laser etched logo at FastTech - Worldwide Free Shipping

these are the ones in my cart (I like plenty of room to work)
- $8.73 Enigma Style Rebuildable Dripping Atomizer - stainless steel / PVD coating / black at FastTech - Worldwide Free Shipping
- $6.84 Patriot Style Rebuildable Dripping Atomizer - 21.7mm diameter / stainless steel / PVD coating at FastTech - Worldwide Free Shipping
- $5.47 IGO-W Style Rebuildable Dripping Atomizer - stainless steel / black plated at FastTech - Worldwide Free Shipping

 

[sando7]

herb here ya go angel cigs USA warehouse, but it only has a single air hole (1coil)
V5 Rebuildable Dripping Atomizer

this one has 2 air holes, for single or double
http://shop.desertvapes.com/product.sc?productId=1334&categoryId=114

plus you'll have them within 3 to 5 days

 

[PaulBHC]

herb how much power is dependent on the coil and how many, not the device itself. I'm sure you have seen this coil calc

Steam Engine | free vaping calculators

click the tab for Battery drain. Play with some numbers and see how many minute or puffs you will get with different builds and even batteries.

 

[sando7]

wonder what ever happened to ManBearPig, he was here but now he is gone...he was a coil wrappin dude?

 

[PaulBHC]

Anyone looking for a genesis tank, good price here as well as some other RDA RBAs

Rebuildable Tanks/RBA | VaporEngine.com

 

[sando7]

took my 14500 Novice RDA and drilled it out to 1/16th & put it on my MVP, man this bad boy hits like a beast,; got a 1.3 build on it....only down side it only holds about 5 drops...but i like it

 

[pufZeppelin]

boy, I’ve been doing about the same
going on about three weeks now, I tightened up an A9 RDA
on my VVv3 and just have been abusing that poor little square battery
4.1v-3.7v , charge , passthru , charge , drain , charge , kinda a torture test
been dripping, taste-testing, clouding, got a lot of paint worn off the shell
of the little innocent iTaste…




Vape≈like ya stole it

 

[herb]

that's not a dripper...it's more like an evod tank...
Eternity Rebuildable Atomizer is the vision ET clone that I use and you can buy premade coils if you don't want to make your own Pre-made Wires and Wicks for Atomizer (50-Pack)

I know that's not a dripper , i saw it while i was on the FT site and thought it sounded very good to possibly add to my arsenal.

I have ONE of those, and it seems to work as good as my real Kanger T3S
- $3.49 MT3S BCC Bottom Coil Clearomizer (3.0mL) - silver / 2.2-2.6ohm at FastTech - Worldwide Free Shipping

but have about a dozen of these
- $2.93 T3S BCC Bottom Coil Clearomizer - translucent / 2.4ml / 1.5ohm at FastTech - Worldwide Free Shipping
the metal band that is friction fit to tank is delicate (in wifes pocket )
but for me, work great, one of my fav’s (holds 3.0 ml contrary to specs)
guess I just like ‘looking’ at the inside goings on

right now I am playing with one of these
- $3.32 RGM2 Bottom Coil Clearomizer (2.0mL) - glass tank / 2.2ohm at FastTech - Worldwide Free Shipping
and I put the base from this on it...
- $2.20 GS-H3 Bottom Coil Clearomizer (2.0mL) - smoke black / 2.4ohm at FastTech - Worldwide Free Shipping
and now it looks like I have a mini MT3S-Glass

- - -
is this what you seek ?

- $6.22 V5 RDA Rebuildable Dripping Atomizer - 1*airhole / laser etched logo / 1.8ohm at FastTech - Worldwide Free Shipping
- $4.97 V5 RDA Rebuildable Dripping Atomizer - 1*airhole / laser etched logo at FastTech - Worldwide Free Shipping

these are the ones in my cart (I like plenty of room to work)
- $8.73 Enigma Style Rebuildable Dripping Atomizer - stainless steel / PVD coating / black at FastTech - Worldwide Free Shipping
- $6.84 Patriot Style Rebuildable Dripping Atomizer - 21.7mm diameter / stainless steel / PVD coating at FastTech - Worldwide Free Shipping
- $5.47 IGO-W Style Rebuildable Dripping Atomizer - stainless steel / black plated at FastTech - Worldwide Free Shipping

Dang Puff, i don't know how you find this stuff lol , thank you very much.

wonder what ever happened to ManBearPig, he was here but now he is gone...he was a coil wrappin dude?

He may still be trying to figure out if he's a man, a bear or a pig or a combination of all three is my guess , i'm sure he'll be back after he figures it out.

 

[Twendt]

Can someone here help me?
http://www.e-cigarette-forum.com/forum/showthread.php?t=575037
Need help with iclear30

Sent from my SM-N900T using Tapatalk

 

[sando7]

Can someone here help me?
Need help with iclear30
Need help with iclear30

Sent from my SM-N900T using Tapatalk

take it back to where you got it and get a replacement

 

[Twendt]

So I am correct in my thinking? I'll see what they say when I go in, it's been this way since day 1 on May 30th. Last time the guy claimed it was because I didn't have things tight enough or were too tight but even after he took it apart and put it back togather it was still the same and I've still had leaking issues into the 510 connection.

Sent from my SM-N900T using Tapatalk

 

[sando7]

yea it shouldn't leak like that, it must be defective it happens some times