- Status
I have watched this review this morning. I have the Spica,the rta witch is the one with Klaus compares to nKFL.
What I understand, is that Klaus have a problem with SVM because they don't made the best MTL atomizer to date.
Please give me a break.
SVM nKFL is so simple, and wonderfull.
Spica is flawless in what is made for.
Why to compare eggs whit strawberry?
What I understand, is that Klaus have a problem with SVM because they don't made the best MTL atomizer to date.
Please give me a break.
SVM nKFL is so simple, and wonderfull.
Spica is flawless in what is made for.
Why to compare eggs whit strawberry?
This morning when I was refilling I decided to re-wick and move the coil up a bit. I moved the coil up to about 2.5mm above the air hole. I am getting a more flavorful vape but notice the drip tip is getting a little warm. Not enough to be uncomfortable but I do notice it is warmer than before. Think the coil might be a tad high but will use it like this till the next refill.
316L 28ga 2.5mm 6 wrap @ 0.75ohm 440deg in TC 20 watts (puff info is only showing a high of 13.8watts). I raised it about the height of the coil is in size. It did seem high to me too. This was as far up that I thought it could go with out touching the top of the bell. I think the extra heat is because the coil is extremely close to the air exit on the bell. I like the flavor but not digging the extra heat. Looking at the Prime and the Lite side by side it looks like the Lite's bell is a little shorter. This is just experimenting and next time I wick I will put in in the middle between my first 1mm and 2.5mm.
It looks like all that own the Lite 2019 are more than happy with the flavor, but I have one thing that is putting me of to get one.
I really like tight smooth draw, I use the Prime on 1st hole, Berserker v1.5 and Berserker mini on 1st or 2nd (depending on the juice), SXK Doggy almost closed and Dvarw with 0.8mm insert.
I came across comments on FB that when the air is reduced the flow is not smooth and its whistling. To all owners of the Lite 2019, can you please share your thoughts and compare the air flow with other atomizers you own.
Thanks!
I really like tight smooth draw, I use the Prime on 1st hole, Berserker v1.5 and Berserker mini on 1st or 2nd (depending on the juice), SXK Doggy almost closed and Dvarw with 0.8mm insert.
I came across comments on FB that when the air is reduced the flow is not smooth and its whistling. To all owners of the Lite 2019, can you please share your thoughts and compare the air flow with other atomizers you own.
Thanks!
On a german sm facebook site Eugen from sm says, as an reply on klaus' youtube review, that they don't produce the af screw themselves and that there might be some variation in production. Due to that fact they add another af screw. So, if one whistles, he recomends to try the reserve screw...
I don't own the new KF lite myself, cause i'm pretty happy with my prime.
The Youtuber's complaint seems to be about the build up of condensation causing the whistling, not the fit of the screw. It wasn't clear to me but he also seemed to indicate that it was wet from cleaning.
I was disappointed that the Youtuber didn't disassemble, clean and DRY the parts. Cleaning seems like a more practical way of solving the problem if it was caused by liquid in the air flow. Instead, he opened up the air flow until he no longer enjoyed it. It doesn't make sense to me.
agreed, he should have paused the recording and corrected his mistake before passing final judgement.
Is there someone here have leak exp through airflow control?
No leaks here.
Mine are still getting to know @vapdivrr 's in customs...but, historically, I'd call it user error if you're leaking through the 510. Usually, it's a wicking or a seal issue. If your wick is touching the air hole under the coil or if you're not air-tight with the assembly of the rta, it'll leak. The only way for liquid to come out of the 510 is for it to start by pouring down the air hole. Therefore, the airflow screw isn't the problem....the problem is upstream.
Hi - Does anyone know how the draw on this compares to a True or a Doggy or a Zenith or... something that's supposed to be MTL-ish?
Is it another one of those loose MTLslike the Zenith? Someone mentioned '1.8mm' - is that its narrowest opening?
Thanks.
Is it another one of those loose MTLs
Thanks.
Air flow is from super tight to semi tight. The loosest I can get is about the Zenith with 2 holes open. It is a true MTL tank, there is no way to get a R-DL with this tank.
I think 1.8 is fully open. Haven recieved mine yet , so not sure how tight, but with that type of AFC, I'm sure it can get really tight
Sent from my SM-G960U using Tapatalk
1.8 is wide open. I'm not sure what the tightest setting is. It's certainly a MTL atty.
Sent from my ONEPLUS 6T
- Status
Similar threads
- Locked
