Mine came with double Orings on the bottom section and the advice I got from the reviewers was remove one because it makes them so tight you can barely turn them to adjust the air flow. Even with one I put VG on it so I can turn it.
Older Folks and Vaping Front Porch - Part Four
- Thread starter MikeE3
- Start date
- th_trl_thread_readers 0
- Status
I LOVE my derringer clone on my REO!!! I was stuck on the nuppin til I got the derringer clone, can't say which one I like better, the derringer is that good.......and it's so much easier to build. Definitely wanna get a couple more of these for bottom feed.
10 X Wholesale Mini Liquid Perfume Funnels Organic Clear Health Plastic Hot Tool
Ya want small funnels, how about 10 for 71 cents
shipped.
There a little small but work great for needle tip bottles.
Ya want small funnels, how about 10 for 71 cents
shipped. There a little small but work great for needle tip bottles.
It must have been 8 wrap according to SE I always loose track so another 8 wrap should come out to about a .6 ohm this one was 1.1. I would really be blowing clouds could go to 150w on my Reauxleux. Probably explode.
You'd probably like the tugboat design too very easy to build either 1 or 2 coils, nice deep juice well.
Nifty idea, thank you for mentioning it!
Hard to get less expensive than that!10 X Wholesale Mini Liquid Perfume Funnels Organic Clear Health Plastic Hot Tool
Ya want small funnels, how about 10 for 71 cents
There a little small but work great for needle tip bottles.
Last edited:
When you vape at the dark side, careful you must be, for the dark side may suck you in
.... I think Yoda said this to Luke ...
10 X Wholesale Mini Liquid Perfume Funnels Organic Clear Health Plastic Hot Tool
Ya want small funnels, how about 10 for 71 cents
There a little small but work great for needle tip bottles.
Welcome to the porch Yiana and Lowjumper. So where you been on ECF until now ... nice to have you join the crowd here.
Been here be four, just don't post much but after 4 pages of funnels I thought I would throw in my
. I think it worked
- Dec 18, 2013
- 2,946
- 56,640
- 79
Yer here and you still have cents? Not to worry. We'll fix that. We have werk do dew!Been here be four, just don't post much but after 4 pages of funnels I thought I would throw in my
I pulled out one of the KF that I build coils for the other night. All filled up and ready to go. But, it acted like it was 'clogged' up or something. No airflow? No juice flow? I don't know.
So, I built another coil for it, and wicked it my normal way instead (bunny ears sticking up). That didn't help. I also tried (on both coils) to remove the second airflow screw to give it lots of air.
In case there's a defect with that one (It's new), I switched to another. Of course, this one is part of the new batch also. But, it seems the same. Almost no vapor coming out.
What am I doing wrong? Could this batch be defective? Has anyone else received KFs from Fluid Vapes? If so, have you tried any of them yet?
Certainly it couldn't be anything that I'm doing wrong? Not little ole me.
So, I built another coil for it, and wicked it my normal way instead (bunny ears sticking up). That didn't help. I also tried (on both coils) to remove the second airflow screw to give it lots of air.
In case there's a defect with that one (It's new), I switched to another. Of course, this one is part of the new batch also. But, it seems the same. Almost no vapor coming out.
What am I doing wrong? Could this batch be defective? Has anyone else received KFs from Fluid Vapes? If so, have you tried any of them yet?
Certainly it couldn't be anything that I'm doing wrong? Not little ole me.
Let's start with this ...
1.) if you just draw through it without pressing the fire button, does it feel tight or does it have reasonable airflow?
2.) if you hold your finger over the air hole and draw. Is it tight, like real tight? It should be, if not there's an air leak someplace. Also if it's tight you should see an air bubble escape from the juice channel feeding the wick. Do you?
Just trying the 'check out' the atty itself w/ this questions. Then if needed we can talk about you coil/wick setup.
You may not hear back from me until the morning ... heading off to bed soon.
Ditto, and the more juice the tank holds, the less often I have to refill it.
<-- notice the gallon jar of joose next to the bear?
Huh, I thought it was Fanta
Wow! Does Fanta still exist? I haven't drank that for about....ummmm... 20 years?Huh, I thought it was Fanta
Does it have 2 screws in the bottom one for fill and one for air adjustment?
And don't some have a screw for airflow adjustment up under the 510 pin?
These are EhPro KF 2+ lites, right?
Did you tear them down and clean them first? Not from Fluid Vapes, and maybe wasn't even EHPro, but I had one some time back had a metal shaving blocking the air intake.
Try taking the air adjust screws all the way out, then use a straightend paper clip to probe both directions - i.e. in through the intake and where the screw was.
And some have found that, with the dual intake ones, if you can't see through the two intakes, you may need to "adjust" the 510 screw so you can. Has to be open for that, as you'll loosen the positive block. If they won't line up, you can use a small o-ring as a "washer" near the 510 screw head.
Yes, the EHPro Kayfun Lite Plus V2 with the 2 air adjustment screw in the bottom of the base.
I did tear them down and clean them before use. I stuck a paper clip in the side air holes and can see the paper clip through the empty screw hole. And, vice versa.
I can't see through the two intakes on any of the ones I have out right now. Not even the one that's working well. OK. Just went and checked ALL of them. I can see through the 2 air holes only on one of them out of 12.
- Status
Similar threads
