Older Folks and Vaping Front Porch - Part Three

Status
Not open for further replies.

Ken_A

Vaping Master
ECF Veteran
Verified Member
Jan 13, 2013
4,876
28,345
Florida
Well, you could clean your toilette with it, but at $37.50 per 30ml bottle, you might want to reconsider :)

CLR-1.jpg
Not sure about anyone else, but that don't look like CLR to me.
 

Wolfenstark

Vaping Master
ECF Veteran
Verified Member
Sep 1, 2014
4,815
14,724
Perth , Australia
I gave the silicon ring plug thing a go on the Lemo.
Its not my thing , you do have to keep tightening the base to make sure its fully tight not just when you meet some resistance.
I can see if you don't have the tabs at the bottom of the threads the ring getting out of place when you screw the base back on.

I don't mind the few seconds it takes to use the fill screw.
 

Wolfenstark

Vaping Master
ECF Veteran
Verified Member
Sep 1, 2014
4,815
14,724
Perth , Australia
If you tighten I til it stops, it defeates the purpose of having the ring(which is a gasket). So just until it feels "spongy" would be my guess.

Nah don't like it - If I did that there is a gap of threads and I wouldn't be surprised if the ring moved with any agitation.
 

DavidOck

ECF Guru
Supporting Member
ECF Veteran
Jan 3, 2013
21,239
178,485
Halfway to Paradise, WA
If you tighten I til it stops, it defeates the purpose of having the ring(which is a gasket). So just until it feels "spongy" would be my guess.

No, it does have to go down tight. Has to be the full ring to prevent the DC plug shaped, well, plug, from getting pulled out when you assemble, as mentioned.

Both it and the screw work fine, of course, and nice to have a choice.
 

Kenna

Vaping Master
ECF Veteran
Verified Member
Aug 14, 2014
7,367
121,493
Texas, USA
That's a pretty odd belated Christmas present, a bottle of toilet bowl cleaner? CalciumLimeRust??

Don't have the V2 MVP, but check the itty bitty manual to see how to read ohms without firing. Should be pretty easy. On the VV3, you just press both the up and down buttons at the same time and hold them both down. Reads, doesn't fire.



While also very similar, if I get to the point where I need stainless or bronze wire brushes, I just wrap a new coil. Quicker :)
:p Castle Long Reserve! But I've changed my mind now. Vaping the last of the tank & going to install the coil & test on the MVP. All of the Innokin vv/vw devices check ohms etc the same way without firing.
 

2legsshrt

Resting In Peace
ECF Veteran
Oct 19, 2009
7,162
107,789
75
Spokane,WA
I gave the silicon ring plug thing a go on the Lemo.
Its not my thing , you do have to keep tightening the base to make sure its fully tight not just when you meet some resistance.
I can see if you don't have the tabs at the bottom of the threads the ring getting out of place when you screw the base back on.

I don't mind the few seconds it takes to use the fill screw.

Do you need to use a needle tip to fill them or will they fill from the bottle like the KFL?
 

PapaSloth

Ultra Member
ECF Veteran
Verified Member
Aug 16, 2014
1,634
10,080
Portland, OR, USA
You guys gotta check this thing out. Enough power to burn your face off, heck you could start your car with it!
https://m.fasttech.com/p/1982900

Sent with no malice and not a whole lot of forethought from my new Galaxy Tab 4. Thanks Santa!

OK, let's do the math. It has a 1200mAh battery (1.2Ah). Output current is 80A max. A full battery charge would last 1.2/80 hours, which is 54 seconds. Hmm. That should be enough for maybe 10 hits or so, before the battery is completely drained.

Buy 30 of them if you plan to vape for the whole day!
 
Last edited:
Status
Not open for further replies.

Users who are viewing this thread