Post pictures of your working wick and coil setup

[juggalofisher88]

I dont think I have ever seen a parallel 30 g, I have been twisting my 30g. How does that vape?

The single one vaped extremely well, i just now took it out and put in a twisted 30g lol.
It heated up quite fast, great vapor and flavor at 6v

I keep coming back to parallel 30g alot here lately. I love how it dont hold heat like thicker wire but still covers alot of wick.

 

[PapawBrett]

If I were to hand twist Kanthal, is it necessary to weld the leads together ?

 

[juggalofisher88]

If I were to hand twist Kanthal, is it necessary to weld the leads together ?

No

 

[BuddyG]

I have more pics on my Instagram
Instagram

 

[The.Drifter]

Decided to give SS mesh wicking another shot so this morning I rebuilt my Sat22 to run on the Robbot ZNA

Was shooting for something simple in the 0.8 - 1.0 ohm range, decided to try this:

So this is what it looks like built, came out to 0.8 ohms

Little closer shot:

Flavor and vape are enjoyable, just got to remember to do the "Genny Tilt" with this build

 

[HazyDayz]

5 wrapes 26g around 3/32 @ .33ohms

Something simple to start my week. Gonna drill out these posts and go with a parallel soon enough.
Oh, and I got them a bit spaced because most of my liquid is 100% VG and it tends to gunk ALOT MORE. Better tasting for me in the long haul if I dont pinch them crazy when I'm done.

 

[AMDTrucking]

Authentic Vulcan

1.0 mm X 0.1 mm Kanthal A1 Flat Ribbon / Rayon wick at 0.344Ω - 40 Watts.

 

[jonny45378]

Single 24 gauge 8 wrap coil around an appox. 1.4mm screwdriver. Came out to .5 ohms. Good flavor on the veritas. I just hate how it's a PITA to build on it.

 

[olivier92200]

Hi all, first attempt to make a micro coil on genesis Senio mini Senisis. it's seem that perfect for me and not so difficult : wire esmokeguru titanium 0.40mm 26G, with silica wick 3mm done 0.60 ohms

 

[KeepItSimpleStupid]

28g twisted .5ohms and tried out a new way to wick it

 

[KeepItSimpleStupid]

28g twisted (one side tighter then the other cause i was just testing out with parallel building with some scraps i found on my build table) worked out nicely - flavor was fantastic

 

[Xobeloot]

Lookin good KiSS!

 

[Fakubaku]

My Veritas build on rDNA ATM, reading at 1.1Ω, works wonders (a single strand of 28ga, 2 strands of 32ga):

Mutation X on a mech, dual twisted 26ga, .3Ω:

 

[vapero]

haven't posted in a while, but I found my sweetspot with a single coil 24g on the quasar
I've been using this coils for 3 weeks so far, longest I've gone and still don't want to change them as they just work

wicked with rayon

impressive heat time, much much better results for me than duals

love those jets!

best setup so far for me gp paps clone 18500 | quasar clone | 2puffs AFC DT clone

 

[AMDTrucking]

Micro coils out, spaced coils are in

 

[Sucker_dad]

24 Guage on a flat spiral. It was a bummer to build without needlenose, and it is not pretty, but this is the best hitting coil I have ever built.

 

[SLIPPY_EEL]

24 Guage on a flat spiral. It was a bummer to build without needlenose, and it is not pretty, but this is the best hitting coil I have ever built.

nice one! it doesnt have to be perfect to work really well but the way i make one is by using a pin vise, you can bend the end of the wire and trap it inbetween the teeth of the pinvise then the other end i hold with pliers, and as you twist the vise to roll up your coil you can either push or pull the wire that is being held in the pliers to make the coils tight or looser.
i like to have a slight gap between mine to, it slows down the heat from drying out the wick to quickly and also gives me more wick coverage.

i'm also with you on it being one of the best allround coils. highly underrated!

 

[KurrptSenate]

Dual tiger is the lancia

 

[The.Drifter]

Micro coils out, spaced coils are in

I like spaced coils too, seems much better for those coil gunking juices.

 

[Sucker_dad]

nice one! it doesnt have to be perfect to work really well but the way i make one is by using a pin vise, you can bend the end of the wire and trap it inbetween the teeth of the pinvise then the other end i hold with pliers, and as you twist the vise to roll up your coil you can either push or pull the wire that is being held in the pliers to make the coils tight or looser.
i like to have a slight gap between mine to, it slows down the heat from drying out the wick to quickly and also gives me more wick coverage.

i'm also with you on it being one of the best allround coils. highly underrated!

Yeah even a decent set of pliers would help. I am going to try a dual coil later.