I don’t know if it’s worth that much trouble to just get a couple caps.
Yeah something like that. I don't find that with the Sceptre coils though. I don't know...there's just something I don't like with the Z coils.
That creates a dilemma for me now. I want that Coolfire mod, but not the Zenith tank on top. Guess i'll have to wait a few months until they sell the mod alone...![]()
I don’t know if it’s worth that much trouble to just get a couple caps.
It's really hard to keep up with the trends. I blame the the Tik Toks, MTV, and MySpace.Don’t feel bad,Javi. I’ve lived in the states all my life and I swear every time I think I know all the slang, another generation comes along and invents a whole new language.
This one has them in stock but not sure about postage to the USWhen I googled it there were only two sites I found and the other didn’t have them in stock
It's really hard to keep up with the trends. I blame the the Tik Toks, MTV, and MySpace.
Ok Mel I've changed over to the 3mm af pin and raised my coil up. Vaping even better/ smoother air. Really like this RBA.That’s the comparison I’m needing. Can’t wait to hear what you think
RDL - So far I'd have to say the Mobb Mini is right on par with the Xeta. Maybe better. Beats the VapeShell and VapeSnail for flavour.
I'm using the exact same 0.5 Ohm Ni80 fused claptons, same cotton and same juice. Both in BBs.
The draw on the Xeta with the widest chimney reducer installed is tighter than the Mobb wide open with the 3.5mm af pin. I'm going to try the 3mm pin today. I'm running the Mobb at around 28W and the Xeta at 24W.
It's still only my first build in the Mobb and I started with the top of the coil just poking up above the top of the posts. Next I plan to try placing it higher so that about half the coil is sitting above the posts. That seems to be the sweet spot according to most pundits. Pretty sure @Hightech Redneck mentioned he a preferred high coil placement.
The post screws are tiny grubs and the SXK version comes with a really flimsy little Allen key. It's not a great fit and feels like it could strip the blighters easily.
@NolaMel I'd recommend using a better quality tool if you have one that small. I don't, but plan to visit the hardware store today to get a set.
There are some decent close up build shots in this review:
RDL - So far I'd have to say the Mobb Mini is right on par with the Xeta. Maybe better. Beats the VapeShell and VapeSnail for flavour.
I'm using the exact same 0.5 Ohm Ni80 fused claptons, same cotton and same juice. Both in BBs.
The draw on the Xeta with the widest chimney reducer installed is tighter than the Mobb wide open with the 3.5mm af pin. I'm going to try the 3mm pin today. I'm running the Mobb at around 28W and the Xeta at 24W.
It's still only my first build in the Mobb and I started with the top of the coil just poking up above the top of the posts. Next I plan to try placing it higher so that about half the coil is sitting above the posts. That seems to be the sweet spot according to most pundits. Pretty sure @Hightech Redneck mentioned he a preferred high coil placement.
The post screws are tiny grubs and the SXK version comes with a really flimsy little Allen key. It's not a great fit and feels like it could strip the blighters easily.
@NolaMel I'd recommend using a better quality tool if you have one that small. I don't, but plan to visit the hardware store today to get a set.
There are some decent close up build shots in this review:
Feel free to jump on me...
I love Innokin..always have, but I just can't get along with their Z coils. I've tried just about the whole range and really trying to like them..but uh uh.
I don't really know how to explain, but they kinda give off a weird flavor that interferes with me...don know, but i've given up on them. Every now and again I go back and re try it..but get the same result.
Gum boots here are called shrimp boots, and they’re white. Poor choice for messy work, but white they areA lot of people around here wear 'em, but I don't know what they call 'em.
You could probably get grub screws of that size somewhere and there are spares in the pack. At least the posts/clamps aren't fragile like the Xeta.Ty. Pretty sure I have one that will fit. Do you think the screws could be replaced? I was hoping for something more durable than the xeta.
Bonus points, Pigs! I do have that sizeOk Mel I've changed over to the 3mm af pin and raised my coil up. Vaping even better/ smoother air. Really like this RBA.
View attachment 946213
I've got a couple of very short ear muffs sticking out the wick ports. I know some people like to cut them flush but I get a bit nervous about not enough cotton covering the holes.
View attachment 946215
The Allen key size for the posts is 0.9mm.
A lot of people around here wear 'em, but I don't know what they call 'em.
Get one of these Ange!
View attachment 946221
It is really comfortable to hold and fire. I thought the squared off design would make it clunky but the battery tube sits in the palm and feels nice.
The cuttaway for the fire button that @hittman mentioned makes it feel smaller than a BB. It fires fast and the extra air compared to a BB really suits the Mobb mini.
View attachment 946225
And with the Xeta
View attachment 946223
Build quality is just like the Mixx

Pretty sure they're unimaginatively called "rubber boots" here.Gum boots here are called shrimp boots, and they’re white. Poor choice for messy work, but white they are![]()
I've used the 0.8, 0.48, 1.0, and the 0.3The flavour from a drop-in, is so hard to translate between different ppl - unless we are all using the exact same juice. And have the exact same tastebuds.
What ones have you tried?
![]()
The 0.3, 0.5 and 0.45 are mesh.
My fave is the 0.3ohm for the airflow and flavour, but I also like the 0.8. If you want to try a 0.3ohm, before you buy the Zenith 2 - I can mail you one.
I've used the 0.8, 0.48, 1.0, and the 0.3
It's not that they taste bad or that Ange. It taste to me that there's something in there...They all have a distinct 'taste' (for lack of a better word) that's different to other coils. I can faintly taste it through my flavors. Thinking about it, I haven't yet picked that up from any other brand of drop in coil.
I think it has to do with what material Innokin uses as a cotton. They do mention in their marketing that the coils lasts longer. That leads me to believe they use a different material.