Terminator/Nautilus/Choddy/Oddy Clone Pics, Tip,Tricks and Quirks

[dwcraig1]

Hmmm...where to source these 2 parts? If they simply replace the tops of the Terms....looks like a nice investment....

Ithaka
They have them right now, as soon as all the pre orders a sent out the extras will be on the site, could be as early as tomorrow.
Also here: THE GOLDEN GREEK MODS :: Ithaka Accessories - e-smokeguru $9 dollars shipping and about 2 weeks to get them.
These will only be available for a short time until the next time

 

[dwcraig1]

BTW...any idea how to get them dang air bubbles to just move on up into the upper tank..Im fed up seeing them.

I ground off the knurling on the JC and rounded over the top in hopes it would give enough room and be smooth enough for the bubble to float on up and juice to flow down....

Using a lot of VG in the mix? Remove more from the base of the mouth piece if is is causing problems like dry or burnt hits other wise just don't look at it. If you are getting when filling use a neddle or tilt and fill slowly.

 

[~Shado~]

Yea....usually a 50/50 or higher VG mix....PG and I don't do so well together....lol

No dry hits...just annoying to see the bubble.....maybe I will take a bit more off in the future if I feel energetic enough....lol

Thx....also, always good to see other Sparky's in the forum....about 30 years in the trade so far....body is worn out from it also, lol...

 

[metaltech]

I'm a little sketchy about the rainbow mkb-ts. If i purchase a real GGTS base for my Term-c,will it screw on the mkb-ts without adapters and have working airflow control?

 

[meowmixmeow]

I'm a little sketchy about the rainbow mkb-ts. If i purchase a real GGTS base for my Term-c,will it screw on the mkb-ts without adapters and have working airflow control?

it works, just that the base O ring that comes with the ggts base is a little too thin, so use the O ring that comes with the term tank.

 

[deezdrama]

it works, just that the base O ring that comes with the ggts base is a little too thin, so use the O ring that comes with the term tank.

What issues can this cause? Cause I never swapped the 510 base oring from the term to the ggts base

 

[metaltech]

it works, just that the base O ring that comes with the ggts base is a little too thin, so use the O ring that comes with the term tank.

Thank You for the info

 

[upsetter21]

Yeah, ppl think the Electrician's don't have hard work, or have "clean" work. It wears you out. I tore my ACL while bending 1 1/4" EMT - one of the reasons I'm on this forum so much. It was incredible I basically tore my ligament with the strength of my own body - the doc says it's an unnatural motion.

Anyway, right on Brother.

Yea....usually a 50/50 or higher VG mix....PG and I don't do so well together....lol

No dry hits...just annoying to see the bubble.....maybe I will take a bit more off in the future if I feel energetic enough....lol

Thx....also, always good to see other Sparky's in the forum....about 30 years in the trade so far....body is worn out from it also, lol...

 

[tagster]

Does anybody know which (if any) parts are interchangeable between the Tobeco clone and the Terminator?

I'm interested in getting the Ody to Kayfun kit and I already own the Tobeco clone. I need to know whether I can just:

A. Purchase a tank extension and use my Tobeco clone (which is why I need to know which parts fit and which don't)

or

B. Purchase an entire new Terminator

Any advice would be much appreciated.

Read the "Upgrade Natilusa" thread. I believe Vochu originally designed the Kayfun conversion for the Tobeco clone. It is only the base threads that matter.

 

[dwcraig1]

Read the "Upgrade Natilusa" thread. I believe Vochu originally designed the Kayfun conversion for the Tobeco clone. It is only the base threads that matter.

Same threads

 

[dwcraig1]

I'm a little sketchy about the rainbow mkb-ts. If i purchase a real GGTS base for my Term-c,will it screw on the mkb-ts without adapters and have working airflow control?

It screws right on, or should

 

[buffalofloyd]

it works, just that the base O ring that comes with the ggts base is a little too thin, so use the O ring that comes with the term tank.

Just for the record, I got 2 GGTS base from COV and I have had no problems with the o-ring that came with them when using my Nautilus, they screwed on perfect, no leaking, excellent stuff... ymmv

 

[tagster]

I believe that is why you have to use the bigger o-ring for the Terminator, because the mouth pieces are a smaller diameter to work with the Tobeco.

 

[dwcraig1]

I had no problems with the o-ring that came installed on the two Oddy GGTS bases that I have.

RE mouthpiece o-rings:
Tobeco's stem is 8 mm
Term, Oddy are 9 mm (9 x 2)

 

[~Shado~]

Ouch!!!
Sorry to hear that. Hope you get back to 100% soon.

Once I hit my 40's...I stopped bending anything over 1"... not enough oomph in the keester anymore...prefab only now.

Sent from my DROID RAZR HD using Tapatalk 4 Beta

 

[Slartibartfast]

BTW...any idea how to get them dang air bubbles to just move on up into the upper tank..Im fed up seeing them.

I ground off the knurling on the JC and rounded over the top in hopes it would give enough room and be smooth enough for the bubble to float on up and juice to flow down....

I don't like that bubble either. I ordered 2 "Ithaka Mouthpiece for Drip Tips" from E-smokeguru (still in stock). 1 for the Hercules I have coming and one for my Terminator-C in the hopes that it will work for both. I don't see why it wouldn't work for the Hercules but I have no idea if it will work out for the Term..."fingers crossed".

 

[dwcraig1]

I don't like that bubble either. I ordered 2 "Ithaka Mouthpiece for Drip Tips" from E-smokeguru (still in stock). 1 for the Hercules I have coming and one for my Terminator-C in the hopes that it will work for both. I don't see why it wouldn't work for the Hercules but I have no idea if it will work out for the Term..."fingers crossed".

It's going to work for the Term ( with the right sized tank, 27 or less mm i think) and if the Herc is an exact clone no problem there either.
But how to get a hold on it to adjust it?

 

[Slartibartfast]

It's going to work for the Term ( with the right sized tank, 27 or less mm i think) and if the Herc is an exact clone no problem there either.
But how to get a hold on it to adjust it?

LOL I don't know...was wondering that myself but I can't imagine it's not workable. Maybe if the rim of it stickes out far enough (before the drip tip) then hemostats?

Or if the drip tip is a tight enough fit.....wow that sounds dirty.

 

[UA72Riddle]

Sweet! My conversion kit finally hit New York yesterday!!

 

[deezdrama]

Sweet! My conversion kit finally hit New York yesterday!!

Awesome... what number was you?

Get pics posted when you receive it please.... and full review lol