Tilemahos new rebuildable part (springomizer)
- Thread starter imeothanasis
- Start date
- th_trl_thread_readers 0
- Status
Doesn't want to let me pm you. Sorry I guess maybe I'll..give it a few and then post what I have to say here.
Maybe you can open a pm conversation with me.
And now I tried something new. I coiled some of imeos' titanium 0.4mm wire 10 full turns at 2.5mm inside diameter and sniped the legs off. It works great. It tastes great. Reads .42ohms.
Titanium springs are a must in my opinion.
Titanium springs are a must in my opinion.
So I'm discussing this now to buy. For those of you with the springomizer how do you feel it does compared to regular. Obviously fiddli must occur to get the right flavor and it's new.
Outside of that Gamow does e tank itself hold up to other tanks like kayfun v4, lite plus, 3.1. Taifun gt2, mark bugs GEM? Etc? What can you all compare it to as better or not quite as good as?
I appreciate it I had ordered a kabuki for post op when I can't build but w springomizer seems just as easy as replacing premade coils and overall if the flavor is better ..
Anyone own this and a kabuki? I'm thinking doubtful but it's worth a shot
Outside of that Gamow does e tank itself hold up to other tanks like kayfun v4, lite plus, 3.1. Taifun gt2, mark bugs GEM? Etc? What can you all compare it to as better or not quite as good as?
I appreciate it I had ordered a kabuki for post op when I can't build but w springomizer seems just as easy as replacing premade coils and overall if the flavor is better ..
Anyone own this and a kabuki? I'm thinking doubtful but it's worth a shot
I had a Kabuki and gave it away, it's OK but not great, it leaked juice through the 510 connection on to my mod.
Also had Kayfun and Taifun. I can assure you, Tilemahos is much better.
The best thing to do is try them all and see which works best for you. IMO Tilemahos is the best tank on the market right now. It has replaced everything else I had previously.
I ordered the Springomizer and it doesn't fit correctly into my V1 Non-AC Tilemahos base. My original part with the channels screws all the way down. The new part stops at a certain point. It would work if I had a longer pin. The pin is about 2mm too short. The pin that came with the Springomizer is a tad too long and I wouldn't be able to use it anyways because of the Non-AC.
I thought I could change out the channel part and keep the original V1 but the air holes on the bottom are opposite from the each other which means the air holes would be completely blocked.
I hope you can understand what I'm saying. I can post pictures of it later so you can understand.
I thought I could change out the channel part and keep the original V1 but the air holes on the bottom are opposite from the each other which means the air holes would be completely blocked.
I hope you can understand what I'm saying. I can post pictures of it later so you can understand.
I just ordered the same, I hope I can get it to work as I ordered the V1 non-AFC with Springomizer internals.
If you buy a complete Tilemahos with Springomizer inside then you should be fine. I got just the Springomizer pieces to update my V1. But I need a longer pin.
if you keep the V1 housing, air holes will stay open Sad, please try it. But I am wondering why the new housing doesnt go deep inside the base
There's a lip on the new housing that stops it from turning. Someone posted a picture of the different housing in this thread some pages back. The V1 housing doesn't have the lip. I will try it again later the way you said imeo, and if I can't get it to work I will post some pictures.
I have the v1 non afc housing and my springomizer fits in no problems, I used the v1 non afc pin as well
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
What about the air holes on the bottom of the housing? The V1 has in the Shape of a "C" on both sides so you can adjust the V1 screws. And the V2 has two normal holes that are opposite the V1 when you compare both to the position of the channels.
these holes are not for air, they are made for the collector tank, thats why I said that the V1 housing will fit Sad
i have ti g1 wire (28awg) sitting here, and while waiting for my springo, i decided to make a few quick springs. 2.5mm coilmaster rod, contact tight coil while winding. ti expands after coiling due to spring and stiffness in the wire, im guessing the id of the spring is 2.7mm or so. slightly expanded the spring pulling it by the ends, clipped off the legs and boom. made 4 coils in 1 minute. now i just have to get my springo delivered to see how they work (in tc).
jesse was amazing. he responded to my late night pm, sent an invoice and shipped all within 30 mins (literally at 11pm pst, 1am his time i think!!!!!!!). super responsive, amazing communication. im an fms customer for all my gg needs (stock up jesse!!). thanks man.
jesse was amazing. he responded to my late night pm, sent an invoice and shipped all within 30 mins (literally at 11pm pst, 1am his time i think!!!!!!!). super responsive, amazing communication. im an fms customer for all my gg needs (stock up jesse!!). thanks man.
Last edited:
it seems that FMS does a great job in USA. I am really glad for Jes and you guys!!
The airflow on mine is ok for my style, its not to loose, good for mouth to lung. You can do direct to lung but it is a little tight.
As imeo said, those holes are to let the excess juice down and not for air
Sent from my iPhone using Tapatalk
direct to lung is easy as you know Lee. Just open a little your lips. I do it all the time and its way better than usual drippers because I adjust my lips even during the inhale without depending on manufacturer's holes
- Status
