Tootle Puffers, Redux (The Sequel)

[LJFinFLA]

have you seen this of many sites...

- http://www.varitube.com/YiHi-SX350-DIY-Parts_c_23.html

I order from them for parts as well as other places. I'm thinking of getting the Renegade 350J kit. I love messing around with building mods. I only wish I had the proper tools to be more creative rather then depend on the standard stuff. I highly recommend that if you are the least bit handy to try your hand at it. Although now it is more cost affective to buy a mod it is very satisfying and pretty easy if you have the patience.

 

[nebulis]

I think I'll wait until Krisma crams her wraps . I don't think I want to go under 1,8 Ohm. And that would be quite a heap of wire

 

[Krisma]

I think I'll wait until Krisma crams her wraps . I don't think I want to go under 1,8 Ohm. And that would be quite a heap of wire

It landed in Adelaide this morning so maybe tomorrow but probably Monday.

Hubby built me this gadget (super x video) to do tension coils and it makes them very tight and perfect. I have been practicing

 

[gt_1955]

I think I'll wait until Krisma crams her wraps . I don't think I want to go under 1,8 Ohm. And that would be quite a heap of wire

http://www.steam-engine.org/coil.asp?mat=ss316&r=1.8&awg=32&id=2&ll=5

Quite doable as a contact coil, width will just be over 2mm

 

[LJFinFLA]

http://www.steam-engine.org/coil.asp?mat=ss316&r=1.8&awg=32&id=2&ll=5

Quite doable as a contact coil, width will just be over 2mm

I really like Steam Engine. Makes building coils so easy.

 

[fourthrok]

For what it's worth, I know that Madvapes sells stuff for building mods and whatnot. Maybe this might help someone? http://www.madvapes.com/mod-builder-parts.html

 

[pufZeppelin]

Its a standing joke with the Aussies that I am not allowed to use power tools or things like soldering irons
so chips are out. All my mods are simple tootle puffing wood mod with kicks. It's enough for how I vape.

so no computin power

just a flashlight with an coil in place of a bulb…

 

[gt_1955]

I really like Steam Engine. Makes building coils so easy.

Pretty accurate for spaced coils, not so much with contact coils (although the SS was spot on)

For what it's worth, I know that Madvapes sells stuff for building mods and whatnot. Maybe this might help someone? http://www.madvapes.com/mod-builder-parts.html

Horrendous postal charges for anything posted from America to anywhere else in the world though

 

[pufZeppelin]

I order from them for parts as well as other places. I love messing around with building mods. I only wish I had the proper tools to be more creative I highly recommend that if you are the least bit handy to try your hand at it. Although now it is more cost affective to buy a mod it is very satisfying and pretty easy if you have the patience.

that’s what I was gonna say

these prices anymore
unless you have the set-up, tools, desire
just pick & add to cart, wait…

 

[Krisma]

http://www.steam-engine.org/coil.asp?mat=ss316&r=1.8&awg=32&id=2&ll=5

Quite doable as a contact coil, width will just be over 2mm

Oops I got 28 gauge that's a lot of coils maybe I need to do a quick order

I was looking at 1.5ohm 3mm diam 13wraps

 

[Krisma]

Pretty accurate for spaced coils, not so much with contact coils (although the SS was spot on)


Horrendous postal charges for anything posted from America to anywhere else in the world though

Mad vapes charges by weight and for small things their shipping is quite good.

 

[nebulis]

It landed in Adelaide this morning so maybe tomorrow but probably Monday.

Mine seems to have a very long siesta in Athens (not moving forward)

http://www.steam-engine.org/coil.asp?mat=ss316&r=1.8&awg=32&id=2&ll=5

Quite doable as a contact coil, width will just be over 2mm

I'll see. And try. Have not done contact coils any more for a long time, somehow I think more spaces - better cotton saturation? And also because I don't do dryburns or any dry heating ups of coils any more.

 

[gt_1955]

Mine seems to have a very long siesta in Athens (not moving forward)



I'll see. And try. Have not done contact coils any more for a long time, somehow I think more spaces - better cotton saturation? And also because I don't do dryburns or any dry heating ups of coils any more.

I didn't dry burn it either, just a slight clean up, wrap and insert. Didn't do a heat and squeeze either (I'm over that ... if I were home, It'd be a tensioned contact coil )

 

[gt_1955]

Oops I got 28 gauge that's a lot of coils maybe I need to do a quick order

I was looking at 1.5ohm 3mm diam 13wraps

But it will only be about 5mm wide as a tensioned cc ... should be okay I reckon?

Edit: If I remember correctly, the B&M had 24, 26, 28 and 30 in stock

 

[gt_1955]

Mad vapes charges by weight and for small things their shipping is quite good.

And here I've been deleting their emails because I thought the shipping would kill me

Thanks

 

[nebulis]

I didn't dry burn it either, just a slight clean up, wrap and insert. Didn't do a heat and squeeze either (I'm over that ... if I were home, It'd be a tensioned contact coil )

I'll give it a try then. Which type SS did you use?

 

[Krisma]

And here I've been deleting their emails because I thought the shipping would kill me

Thanks

I buy small stuff all the time. You do have to play with the cart a bit. Also they are one of the companies where 2 small orders with separate postage are cheaper than I combined order (shipping cost)

 

[gt_1955]

I'll give it a try then. Which type SS did you use?

SS316 ...

 

[Krisma]

I'll give it a try then. Which type SS did you use?

I got 316L not sure what is the best. It's my first go at it.

 

[fourthrok]

Out of curiosity: I'm a bit concerned about my husband and if things get hard for him to get what he needs for his vaping. He's even more Tootle-Puffy than many of the Tootle Puffers in here, only vaping maybe 1 ml. a day (if that) and he uses the old fashioned Joye and Smok eGos and carto tanks. But he does vape about 11mg juice. I have not been able to replicate the juice he likes (Double Mint from MVS), unfortunately. Soooo....I was wondering. Will 0 nicotine juice be banned too? If I got a mess of his juice in 0 nic and stored it...couldn't I add an appropriate amount of my 60mg nicotine juice to it to make 11mg? (whatever that equation would be...maybe someone here can help me out with that). I have a crate FULL of cartomizers...mostly 2.1 and 3 ohm, but I know he likes 1.7, but heck...he could get used to things if he had to, right? I even have some lightly used Twists so he could adjust the voltage to accommodate. I also have a huge collection of eGos I've been buying on clearance for awhile. Most are lightly or barely used. He can make a cartomizer last a month, easy...haha! That would get him through quite awhile, I'm thinking. What do you think? He's talking (bitterly) that at least Medicare ought to give him patches if they push this anti-vaping through. He's very unhappy right now.