Tootle Puffers, Redux (The Sequel)

[AndriaD]

I have a Magma it is a little bed wetter. Other than that I like it.
I think what happens is vapor condenses on the top cap run down across the deck and out the air intake. I may dremel it into submission.

I'm thinking about getting a 12ga needle and fixing that wetting problem with mine; if it didn't leave juice on my fingers everytime I touch it, I'd like it a lot better. I determined (by asking him!) that my husband does in fact have a cutting wheel for his Dremel, so it's entirely possible, I just need that 12ga needle.

Andria

 

[Oregon Linda]

I'm thinking about getting a 12ga needle and fixing that wetting problem with mine; if it didn't leave juice on my fingers everytime I touch it, I'd like it a lot better. I determined (by asking him!) that my husband does in fact have a cutting wheel for his Dremel, so it's entirely possible, I just need that 12ga needle.

Andria

I'm not following you, Andria. How would a 12 ga needle fix the leaking problem?

 

[LJFinFLA]

Yeah, but mine only took 30 seconds to build!

In all seriousness, though, it's really amazing what you can do with a little bit of ingenuity. I was ready to throw my Kayfuns in a drawer because they hate me. But I'm getting a nice vape with this one in dripper mode.

Oh No! Now your going to be a Mod Womper with one of your new Mech Mods and a Kayfun Dripper!!!

 

[DingerCPA]

According to Steam Engine, though, you would need 13/14 wraps to get a 1.3 ohm coil. That's a lot of wraps for quite a few rta/rdas. I've thought about trying ss wire, but wish it came in smaller gauges. It would be easier to get my target resistances.

Yeah, that was what I was finding as well. So I still need my kanthal for my PT2s. I'll keep a'lookin

 

[Oregon Linda]

Oh No! Now your going to be a Mod Womper with one of your new Mech Mods and a Kayfun Dripper!!!

Naw. I still drip at 8 watts.

 

[AndriaD]

I'm not following you, Andria. How would a 12 ga needle fix the leaking problem?

Insert in the airholes, and cut off at (I think?) about 1/8th-1/16th inch above the deck level; the juice that always lays about on the deck seems to be the reason it leaks, when it (inevitably) runs into the airholes; if that juice couldn't get down into the airholes, I think it would fix it. I already have a 15mm o-ring under the AFC ring, so I think the raising of the level of the airholes with the 12ga needles would do the trick.

Andria

 

[Belhade]

Actually, it's spalted maple from a fallen maple tree. I had a friend (who owns a CNC router) cut the outline and the top routs. I took it from there. It does look unfinished, because it's only finished with natural oils with no pigment. The sides and back have an oil finish with a "vintage tint". If you could feel it, it feels very smooth and silky.

The neck is canary on canary, and I cheated there--I had it made to spec by Warmoth. I don't trust myself working with woods that cost more than or are harder than maple, and canary wood is both.

Her name is Tammy.

Do you play?

Very nice.

I have a guitar; it's a Tele clone (SX Furian) and I bang on it every now and then, but I wouldn't say I play.

 

[MikeyConti]

According to Steam Engine, though, you would need 13/14 wraps to get a 1.3 ohm coil. That's a lot of wraps for quite a few rta/rdas. I've thought about trying ss wire, but wish it came in smaller gauges. It would be easier to get my target resistances.

Hopefully they will come out with different size's..

 

[Robert Cromwell]

I put dual single wire 30 ga 1.8 ohm coils in my Velocity mini. This might work. Tootle Klowds galore! Easy lung hit with at least twice the vapor as a T3.
don't care much for the chuff tip though. Regular drip tip for now at least. Untill I get my Mod Womper wings.

Now I will have to make up some 3mg juice...
And cut down to 4% on the Vanilla custard flavoring....

Sub tank mini will probably be here tomorrow.

 

[Katdarling]

The things I learn on ECF. I'm not only a tootle puffer (Provari 2.0 and 2.5 sporting z-atty-pros), I'm a tootle puffin' ole fartress. Do I get a cookie or sumptin?

I have a couple of hairy wristbands, a few odd looking smiley fish, or an actual authentic membership card.

Whatcha want, dear one?

 

[Krisma]

The cero tanks arrived this morning. Too much on the go to try them

 

[3mg Meniere]

The cero tanks arrived this morning. Too much on the go to try them

I was about to say Sunday?? when I realized that today is Monday for you.

 

[Katdarling]

The cero tanks arrived this morning. Too much on the go to try them

Hiya upside down girl!

Cerotanks, you say?

 

[Woofer]

Mine was a tad more complex than that. I modified the KFL topcap so it fits over the coil and has top airflow.

So how does she vape?

 

[Boden]

So how does she vape?

Really well

Night all

 

[Woofer]

I'm thinking about getting a 12ga needle and fixing that wetting problem with mine; if it didn't leave juice on my fingers everytime I touch it, I'd like it a lot better. I determined (by asking him!) that my husband does in fact have a cutting wheel for his Dremel, so it's entirely possible, I just need that 12ga needle.

Andria

Yes the needle should help, perhaps even fix the problem entirely. Wouldn't that be grand! The other option is to grind the entire flat deck so that is slopes back toward the juice wells. I can not determine how much leakage if any gets past the threads.

 

[fourthrok]

I have a couple of hairy wristbands, a few odd looking smiley fish, or an actual authentic membership card.

Whatcha want, dear one?

Pick the odd looking smiley fish! Pick the odd looking smiley fish!!!

 

[Katdarling]

You're obviously fish prone, 4th.

 

[Drummel]

That Cherry colors one looks AMAZING! I love it. Well spent I say!

 

[Electrodave]

Actually, I DO have a few things to say on the subject, but I can not do that now. I have to put some pieces together (after completing a bit of research), and then I will be more than happy to engage in the discussion with you.

But before I can even do that....... I have to go vegetable shopping!!!!!!

So, you'll wait for me, please?

(Like you have any choice.....)

I'm still here, and there's still a cartotank on top of my eVic.

Yeah but for $2.90 shipping included I don't mind leaning left to hit on it.

Must have come from Fasttech--am I right? At the very least, you, I and Lord Cromwell are all lung hitting tootle puffers.

Tootle huffers.

Convert to the dar.. Womper side. Free cupcakes on Wednesday

Coffee, too?

I put dual single wire 30 ga 1.8 ohm coils in my Velocity mini. This might work. Tootle Klowds galore! Easy lung hit with at least twice the vapor as a T3.
don't care much for the chuff tip though. Regular drip tip for now at least. Untill I get my Mod Womper wings.

Now I will have to make up some 3mg juice...
And cut down to 4% on the Vanilla custard flavoring....

Sub tank mini will probably be here tomorrow.

I hate to see such a good person slowly descending into the pits of heck...