WOFOTO Profile RDA
- Thread starter Steve W Pedersen
- Start date
- th_trl_thread_readers 0
- Status
On a roll here running Profiles on Reo P67's. Have had the TRA P67 set up with a Matte Steel that paved the way; the Hammertone P67 now wears a Gunmetal; the Gold one will be here tomorrow for the Black Wrinkle P67; and I just ordered a Matte Black one that will be here in 2-3 days for the Storm Trooper P67. So another Goon and Kryten have lost their places. The custom Metallic Copper P67 I'm leaving as is with a Black Goon on it. I want to keep at least one of them on line (I have 8-9 Goons, but all but this one have lost their places). I know it's sacrilege, but I kept two of the 6 Krytens sort of alive for now too by putting them on a couple of junk squonk mods I have (iJoy Capo). I loved the Krytens in their day, but mesh rda's have won just about all of my attention now days.
So I guess this means my five P67's are now out of retirement after being out of sight for quite some time. It's kind of funny in a way that with all the high end BF atty's I have that couldn't keep them or any of the many other Reos I have alive, these far cheaper mesh atty's will breathe new life into these. The P67's are the best Reos ever made, so the combo is a win-win with the Profiles.
So now 3 Profiles will be on regulated squonk mods and 5 will be on mech squonk mods. Guess I'll have to update the P67 X 5 picture I posted above when four of them are setup with Profiles.
Edit to ad: USPS tacking shows that the 2 new Profiles are out for delivery to me today (Tuesday).
So I guess this means my five P67's are now out of retirement after being out of sight for quite some time. It's kind of funny in a way that with all the high end BF atty's I have that couldn't keep them or any of the many other Reos I have alive, these far cheaper mesh atty's will breathe new life into these. The P67's are the best Reos ever made, so the combo is a win-win with the Profiles.
So now 3 Profiles will be on regulated squonk mods and 5 will be on mech squonk mods. Guess I'll have to update the P67 X 5 picture I posted above when four of them are setup with Profiles.
Edit to ad: USPS tacking shows that the 2 new Profiles are out for delivery to me today (Tuesday).
Last edited:
Finally set up the two newest Profiles on the Black Wrinkle and Storm Trooper Reo P67's, so now have 4 Profiles on P67's. On the Reos they are hitting at about 100W, so they do use up joose with my DLH's. But with the larger capacity silicone bottles I have in the Reo's joose usage is a non issue.
Have 8 Profiles now to go along with 9 DMP's and 3 VVM's... that ought to be enough mesh RDA's to see me through.
Have 8 Profiles now to go along with 9 DMP's and 3 VVM's... that ought to be enough mesh RDA's to see me through.
Can never have too many Profiles!! I’m currently capped out at 7 which I feel at this point of time is sufficient. They all reside on my most preferred and used devices - with a couple of other devices using my other RDA’s just so they do not feel left out. Almost positive 7 will not be my final number!
Rumor has it Wotofo is working on a Profile RTA. @diagrammatiks posted this last week.
Rumor has it Wotofo is working on a Profile RTA. @diagrammatiks posted this last week.
Wotofo has been staying in the Profile game so far. This suggests they will continue to do so. But I'm not a fan of all the chimney RTA's I have from the TC days and didn't use much. I much preferred the RDTA's over them (especially the Avocado Genesis and Avocado 24's). Never say never, but up front I would have little or no interest at all in any chimney RTA, not even one that uses mesh.
Heads up Profile fans, myfreedomsmokes has the Profile for $16 right now. I just got one from ecig-city for $20 and thought that was great. It’s gonna be hard to resist this deal.
Edit: ecfdisc14 for 14% off, crazy good deal
Edit: ecfdisc14 for 14% off, crazy good deal
Great heads up.
This kind of giveaway pricing suggests that they are going away (vendors not restocking them again). If you want more Profiles you might want to grab while the grabbing is good.
The Frosted Black Profile did not win me over like all the others did and will not be used. So I am stopping at the eight in service. I got it for the lowest price I paid for any of my other Profiles ($23.76 shipped). So no foul since its been relegated to being a back up spare deck/parts for the other eight.
Totallly agree with you! Mesh is nice, and after all, it's nice to have new experiences and try new products in this booming vape world, but even a simple good build on that RDA provides a more intense flavour experience than the mesh.
Another thing i noticed is that using mesh is way more prone to get a nasty and sudden dry hit.
Also, the ammount of cotton used to properly wick the mesh on this RDA, i think that's enough for like 2 / 3 builds on 3mm coils.
What can i say, i liked the experience, but using the RDA that much daily. Even for a single coil usage, i tend to select others in the collection. Still a nice RDA and the build quality is pretty good for the price tag.
I'm attaching a #handcheck that i posted on Instagram some time ago! It really looks nice on the Pulse Mech Squonk
Props to all! Keep it cloudy fam!
The Profile does take a boat load of cotton - 3 to 4 times that of a single 3mm coil. But I have found that despite this amount, it lasts so much longer than a typical coil setup. I am a fan of sweet dessert juices – a typical coil I would re-wick at least twice a week. With the Profile, one a month, even longer. So yes, from the outside it does look like it uses much more cotton which could be a cost factor to some. But once we dig into the details, I would say with worse case it is on par with typical coil and in most cases uses even less.
It is unforgiving should it not be wicked properly. Critical that the cotton is firmly pressed against the mesh avoiding any voids which leads to hot spots. And if going dry, it does not taper off like a coil setup would. Once the flavour starts to drop, saturate your wick to prevent that brutal dry burn. Slight learning curve over a coil but once you get use to it dry burns becomes a thing of the past.
It is unforgiving should it not be wicked properly. Critical that the cotton is firmly pressed against the mesh avoiding any voids which leads to hot spots. And if going dry, it does not taper off like a coil setup would. Once the flavour starts to drop, saturate your wick to prevent that brutal dry burn. Slight learning curve over a coil but once you get use to it dry burns becomes a thing of the past.
Mine new Profile will be here Monday from myfreedomsmokes. Great deal and as always a great vendor. I used to get my nicotine from them so I’ve ordered quite a bit from them and they always ship fast. Now they need to end that sale on the Profile so I stop ordering them.
I ordered my Profile from myfreedomsmokes on Thursday and got it today (Saturday), great job, great price, and fast shipping. There is some crappy vendors out there but myfreedomsmokes is not one of them.
I ordered my Profile from myfreedomsmokes on Thursday and got it today (Saturday), great job, great price, and fast shipping. There is some crappy vendors out there but myfreedomsmokes is not one of them.
Last edited:
I missed the sale the first time, but just checked and it’s on again. Thanks for the heads up madstabber.
Has anyone tried the OFRF mesh and found isn’t so good for flavor compared to the WOTOFO mesh?
Has anyone tried the OFRF mesh and found isn’t so good for flavor compared to the WOTOFO mesh?
Flavor is subjective to many things, including your own personal tastes that will likely not be the same as mine or anyone else's.
My DIY is nic free, so mixing it for personal flavor is what's important to me. Which mesh I use in any of my mesh RDA's depends on the joose and which mod I will be vaping it on. Since I use 18650 mech & dual para batt mech squonk and 20X700 regulated squonk mods to run my mesh RDA's at various power levels, between them I use the KA1 that comes with the Profile in some, the OFRF nexMesh KA1 in others and mesh cut from rolls/sheets of SS mesh I have on hand for others as well. The matched combos I use give me stellar flavor to my personal tastes in my mesh RDA's no matter which ones they are (WPM's, DMP's or VVM's).
My DIY is nic free, so mixing it for personal flavor is what's important to me. Which mesh I use in any of my mesh RDA's depends on the joose and which mod I will be vaping it on. Since I use 18650 mech & dual para batt mech squonk and 20X700 regulated squonk mods to run my mesh RDA's at various power levels, between them I use the KA1 that comes with the Profile in some, the OFRF nexMesh KA1 in others and mesh cut from rolls/sheets of SS mesh I have on hand for others as well. The matched combos I use give me stellar flavor to my personal tastes in my mesh RDA's no matter which ones they are (WPM's, DMP's or VVM's).
Mine just came in from MFS and is in a dawn bath, have a basic rda clone on my squeeze 2 at the moment that is mighty tasty still so waiting until I run out of the juice to try it. Sounds like it is going to be pretty good.
I got impatient and just put it on my drone 250C, and not bad at all. 16 bucks well spent for my first mesh rda. SS one looks like crap on the ultem/black drone, it will look much better on the squeeze 2 as I intended later.
Squeeze 2 and Profile is a mighty fine vape. It is my fave regulated squonk combo right now. The Profile on my P67 is my fave mech squonk as well. Tried several different combinations and I am in vape bliss with these two. It will be tough to swap out for quite awhile.
Six of my Profiles are on mech squonk mods..... the other 3 are on regulated squonk mods (one on a Pico Squeeze 2, two on Sig Fuchai's).
DT-DS Dual Para Batt Mech Squonk.
Reo P67's.
DT-DS Dual Para Batt Mech Squonk.
Reo P67's.
I've seen a few people talking about how good the profile/P67 combo is,so i'll finally get to find out for myself later in the week,i made a great trade deal for a P67.I felt left out without one haha.And of course it will be topped with a profile.
I have a couple now. Like the OP I've had a Themis Mesh RTA for a while. So a couple of weeks ago I got my first Profile. I got one on a Feedlink unregulated and the other on a Squeeze 2 with nexmesh.
How offten do you squonk these RDAs? Or a better question, how many pulls are you getting after pressing the bottle? I find myself squonking every other pull. I probably don't need to that much. But I want to ensure I'm not frying cotton. Another question, has anybody here tried actual mesh in one of these (Opposed to strips)? I'm talking the screen styled mesh.
How offten do you squonk these RDAs? Or a better question, how many pulls are you getting after pressing the bottle? I find myself squonking every other pull. I probably don't need to that much. But I want to ensure I'm not frying cotton. Another question, has anybody here tried actual mesh in one of these (Opposed to strips)? I'm talking the screen styled mesh.
- Status
Similar threads
- Locked
