iTaste MVP v2 Owners Group
- Thread starter KnurledNut
- Start date
- th_trl_thread_readers 0
- Status
Just a small update. I checked it and it was legit. Thank you to all who pointed the scratch off code and verification.
I was shocked at how long the MVP2 charge lasts! I took it to work with me. (I work 4 nights on/4 nights off. 13 hour shift.) I had vaped on my MVP2 for 2 off days, and I figured my first night working I would need to charge it when I got home. It was still showing green. I took it in with me the next night, same thing. Still showing green when I got home. Not until my last night did it go to yellow. That was effectively 6 days of vaping before I needed to charge it. (I didn't want it to go into the red.) Now, I vape a lot like how I used to smoke. Every hour or two, I would vape for about 15-30 minutes. I was seriously amazed at how long it held it's charge! I had heard it goes on and on by others, but to have it go on as long as it did was really astounding! The 6 days of charge was straight out of the box as well. Really a great item, and I couldn't suggest it to others any more highly.
(The MVPs is fully charged when the green light goes off. Is this correct?)
(The MVPs is fully charged when the green light goes off. Is this correct?)
Last edited:
(The MVPs is fully charged when the green light goes off. Is this correct?)
Yes it is charged when the green light goes off.
I was shocked at how long the MVP2 charge lasts! I took it to work with me. (I work 4 nights on/4 nights off. 13 hour shift.) I had vaped on my MVP2 for 2 off days, and I figured my first night working I would need to charge it when I got home. It was still showing green. I took it in with me the next night, same thing. Still showing green when I got home. Not until my last night did it go to yellow. That was effectively 6 days of vaping before I needed to charge it. (I didn't want it to go into the red.) Now, I vape a lot like how I used to smoke. Every hour or two, I would vape for about 15-30 minutes. I was seriously amazed at how long it held it's charge! I had heard it goes on and on by others, but to have it go on as long as it did was really astounding! The 6 days of charge was straight out of the box as well. Really a great item, and I couldn't suggest it to others any more highly.
(The MVPs is fully charged when the green light goes off. Is this correct?)
Me too and I can't understand the longevity of the unit. There must be some different chemistry with the MVP battery.
put mine on the charger with ~900 puffs and 3.7V showing on the battery. The one thing i caution about is that when you go yellow its like two tokes till red and shutdown. 
i was getting a lot more but with the Russian 91 @ 10watts and doing more long lung inhales i am using the battery a little harder than i was before.
i was getting a lot more but with the Russian 91 @ 10watts and doing more long lung inhales i am using the battery a little harder than i was before.
I have experienced the quick jump from yellow to red as well. It is rather strange since other Innokin color buttons seem to be a more accurate representation of the charge.
Here are the official numbers
4.2 to 3.75 (green)
3.75 to 3.63 (yellow) (note that there is only .12 volts in this band)
3.63 to 3.3 (red)
Below 3.3 volts Won't fire.
Also, if you look at most Li-Ion/LiPo discharge curves, 3.6 volts is just about right at the threshold where cell voltage RAPIDLY drops off.
A lot of people assume that yellow means you have 50% charge. This is not true.
If you are sporting yellow, you should be looking for a USB port.
And yes, Kayfuns and Russians do affect battery life. The attys take a little bit longer to heat up, we tend to take longer draws on them, and they tend to run at higher watts than say a Mini PT2. For example. I run my Kayfun's "low" at 8.0 watts. I could never bring a Mini PT2 above 7.0 watts without burnt taste.
4.2 to 3.75 (green)
3.75 to 3.63 (yellow) (note that there is only .12 volts in this band)
3.63 to 3.3 (red)
Below 3.3 volts Won't fire.
Also, if you look at most Li-Ion/LiPo discharge curves, 3.6 volts is just about right at the threshold where cell voltage RAPIDLY drops off.
A lot of people assume that yellow means you have 50% charge. This is not true.
If you are sporting yellow, you should be looking for a USB port.
And yes, Kayfuns and Russians do affect battery life. The attys take a little bit longer to heat up, we tend to take longer draws on them, and they tend to run at higher watts than say a Mini PT2. For example. I run my Kayfun's "low" at 8.0 watts. I could never bring a Mini PT2 above 7.0 watts without burnt taste.
yep - i vape in the office with the Russian at about 8.0 watts... when i am in the car or at home it is at 10 or 10.5 watts on the MVP. The mini PT2 for me with rebuilt heads and cotton is good at 7.5 to 8.0 watts max.
put mine on the charger with ~900 puffs and 3.7V showing on the battery. The one thing i caution about is that when you go yellow its like two tokes till red and shutdown.
I vape Evods at 7Watts - I got ~1100 fires from three different MVP2s 5 times total - very consistant
I vaped my MVP an entire cycle with my new KFL+ BE at 10 Watts - 940 fires - better than expected
I think the number might climb a little on successive tests.
The first time I took giant draws for the first hour or so until got over-nic'ed
Now that the novelty's worn off I think I'm taking smaller draws that approximate the "hit" I get with Evods.
The Kayfun is a flavor monster so the same "hit" tastes so much stronger and cleaner.
stock evods with original small posts from last April/May vs 30g kanthal/CVS sterile cotton
Love the avater Tom!
Bill The Cat was my favorite sports personality
I totally agree! I miss that comic.
My spinners seem to push the center-pin on the T3Ss a little more than the MVP. If I take an ego topper off a spiner and put it on the MVP, it won't fire. I have to pull the pin a little and then I'm good to go. Pain in the ..., so I mostly just use my 510 tanks on the MVP. It's not really my walking around mod, so it's not much of a sacrifice.
hey whats up...?
just wanna say for the record-"My spinners seem to push the center-pin on the T3Ss a little more "
spinners don't push, You Do
best advice is to 'look away' as you tighten any topper on
then just as you feel it touch, you're done...
never a need to over tighten, they are threaded on enuff they will never fall off
on occasion my PV qwit working, duh, tank is loose... (snug it back down, lightly)
Vape≈Happy
hey whats up...?
just wanna say for the record-"My spinners seem to push the center-pin on the T3Ss a little more "
spinners don't push, You Do
best advice is to 'look away' as you tighten any topper on
then just as you feel it touch, you're done...
I've been operating under the same assumption, but so far haven't found the 'sweet spot' on the spinner. It seems that if I get it to where it feels snug (I know not to overtighten) it won't fire on the MVP. I'm trying to adjust my definition of 'feels snug', though.
Last edited:
My JWraps is here! Wow they're quick!
I just had to get the R2D2 one, love them on MPVs!
They also threw me a freebie, the Biohazard one :O
BIG props to JWraps! Amazing customer treatment!
Now, I need to get one more MVP to wrap it in the biohazard wrap! xD
I just had to get the R2D2 one, love them on MPVs!
They also threw me a freebie, the Biohazard one :O
BIG props to JWraps! Amazing customer treatment!
Now, I need to get one more MVP to wrap it in the biohazard wrap! xD
Last edited:
My JWraps is here! Wow they're quick!
I just had to get the R2D2 one, love them on MPVs!
They also threw me a freebie, the Biohazard one :O
BIG props to JWraps! Amazing customer treatment!
Now, I need to get one more MVP to wrap it in the biohazard wrap! xD
That looks so cool!
- Status
Similar threads
