With a lot of people like the Dvarw tanks I have begun researching some options again. Anyone have any thoughts on this version? It seems well liked by the fasttech reviews.
$14.95 Dvarw MTL V2 Styled RTA Rebuildable Tank Atomizer - 5ml / 316 stainless steel + PC / 22mm dia. at FastTech - Free Shipping
$14.95 Dvarw MTL V2 Styled RTA Rebuildable Tank Atomizer - 5ml / 316 stainless steel + PC / 22mm dia. at FastTech - Free Shipping
I've tried, I think nearly all of the DL Dvarw's and they all work really well. I don't think you'll go wrong with this one either if you like MTL...again the OG is well loved by the MTL crowd.
Having said all that SMT is right to suggest sticking with SXK or YFTK as they are known for their quality machining.
I hope this helps
Well guys I'm impressed with my Skyline. I went for it on the build with an Ni straight round wire 26 gauge 2.5 Id, 0.4 ohm and following the wicking method which you can watch on Mark Todd's video or see it described on the fasttech forums.
The coil compartment is really small which makes for fantastic flavour....dare I say it....but I'm getting slightly better flavour than in my Dvarw's but this is probably also due to the new build because there isn't much in it.
I had to thin my tails out a lot to be able to get the cotton between the air intake and the wicking port hole and have had no leaking so far. It's a RDL which is very slightly more restricted than the Dvarw DL but this may be down to cotton quantity and I'm going to try a bit less on the next wick change. Obviously juice control closed to top fill the tank and then I opened her wide open to vape although this may be reduced for MTL using higher ohm coils.
This tank is a really good buy for either the MTL or the RDL guys as it comes with two separate MTL inserts to reduce the coil air intake and of course you have a lot of flexibility with the airflow adjustment ring.
In my opinion this is one that everyone should have in their vaping kit selection and it gets a top recommendation from me.
Enjoy you guys and @Redbird11 don't hesitate.....this one's got it all and it's dead easy to build on.
The coil compartment is really small which makes for fantastic flavour....dare I say it....but I'm getting slightly better flavour than in my Dvarw's but this is probably also due to the new build because there isn't much in it.
I had to thin my tails out a lot to be able to get the cotton between the air intake and the wicking port hole and have had no leaking so far. It's a RDL which is very slightly more restricted than the Dvarw DL but this may be down to cotton quantity and I'm going to try a bit less on the next wick change. Obviously juice control closed to top fill the tank and then I opened her wide open to vape although this may be reduced for MTL using higher ohm coils.
This tank is a really good buy for either the MTL or the RDL guys as it comes with two separate MTL inserts to reduce the coil air intake and of course you have a lot of flexibility with the airflow adjustment ring.
In my opinion this is one that everyone should have in their vaping kit selection and it gets a top recommendation from me.
Enjoy you guys and @Redbird11 don't hesitate.....this one's got it all and it's dead easy to build on.
The Gear has been built! I was excited to see the rainbow I ordered (because everything else was oos), was stainless when I opened the box!! Threw a .6 spaced coil in, checked for hot spots, quickly wicked.... and POOF! wick up in flames 
Managed to not catch the whole bathroom on fire at least. Well, it’s up and running. I’ll make a decision on it later.
Managed to not catch the whole bathroom on fire at least. Well, it’s up and running. I’ll make a decision on it later.
You guys are killing me. Too many seemingly good choices! Here's what I'm gonna do. I'm just going to give a some of you folks one of my credit card numbers. Then you can choose what I get and I won't have to think about it anymore.Well guys I'm impressed with my Skyline. I went for it on the build with an Ni straight round wire 26 gauge 2.5 Id, 0.4 ohm and following the wicking method which you can watch on Mark Todd's video or see it described on the fasttech forums.
The coil compartment is really small which makes for fantastic flavour....dare I say it....but I'm getting slightly better flavour than in my Dvarw's but this is probably also due to the new build because there isn't much in it.
I had to thin my tails out a lot to be able to get the cotton between the air intake and the wicking port hole and have had no leaking so far. It's a RDL which is very slightly more restricted than the Dvarw DL but this may be down to cotton quantity and I'm going to try a bit less on the next wick change. Obviously juice control closed to top fill the tank and then I opened her wide open to vape although this may be reduced for MTL using higher ohm coils.
This tank is a really good buy for either the MTL or the RDL guys as it comes with two separate MTL inserts to reduce the coil air intake and of course you have a lot of flexibility with the airflow adjustment ring.
In my opinion this is one that everyone should have in their vaping kit selection and it gets a top recommendation from me.
Enjoy you guys and @Redbird11 don't hesitate.....this one's got it all and it's dead easy to build on.
Everyone wins! I can't think of any downsides to this plan.
The Gear has been built! I was excited to see the rainbow I ordered (because everything else was oos), was stainless when I opened the box!! Threw a .6 spaced coil in, checked for hot spots, quickly wicked.... and POOF! wick up in flames
Managed to not catch the whole bathroom on fire at least. Well, it’s up and running. I’ll make a decision on it later.
View attachment 899469
Fire bad!
Thanks for the info. I asked the question originally before realizing that it was 16mm tank. That seems really tiny. I would imagine it is more difficult to build on that a bigger tank. I still think I'll end up getting a Dvarw though.
There's a 22ml MTL Dvarw as well. I just liked the smaller stature of this tank.
Coppervape Dvarw Style MTL RTA 316SS PEI 5ml 22mm Tank Atomizer
The Gear has been built! I was excited to see the rainbow I ordered (because everything else was oos), was stainless when I opened the box!! Threw a .6 spaced coil in, checked for hot spots, quickly wicked.... and POOF! wick up in flames
Managed to not catch the whole bathroom on fire at least. Well, it’s up and running. I’ll make a decision on it later.
View attachment 899469
Glad you and the bathroom are ok Mel.
Very interested in hearing what you think of the Gear. You probably haven't heard this, but I really like mine...
Yep. I know, there seem to be a lot of sizes and options of Dvarw. I am just looking through some of the options. Right now I am kind of thinking about these two options:
$14.95 Dvarw MTL V2 Styled RTA Rebuildable Tank Atomizer - 5ml / 316 stainless steel + PC / 22mm dia. at FastTech - Free Shipping
$21.31 Dvarw MTL FL Styled RTA Rebuildable Tank Atomizer - 2/3.5/5ml(22*19mm (OD*ID)) / w/ 10*air inserts / stainless steel + glass / 22mm diameter at FastTech - Free Shipping
With this build it strikes me as a little thirsty. Flavor is ok. Probably a little better with a different build?? I think this is a Ni 3mm. It’s a nice smooth draw though. No turbulence or noise. Playing with the af now. It has possibilities if I can get it’s juice consumption down. At 17 w I shouldn’t be emptying a tank this quickGlad you and the bathroom are ok Mel.
Im saving for one myself, and a DL version. There's a store that imports it here, but I think they closed during this auspicious lockdown event.
Hey all... just a heads up on my latest Fasttech order...
The Ares has a new scheduled ship date of 8/12, and the Dwarv is still sitting at 8/10....
I'm willing to give the Dwarv (the one with all the inserts) until the 10th since this is DHL shipping, but I'm not willing to go beyond that. If the Ares isn't in on the 10th with the Dwarv, then I'm removing it from my order...
And if they extend that Dwarv any longer, then it's getting booted too
The Tripod, The Nibiru, and the X is all ready to ship, with the Brunhilde not going to be ready until the 6th now (an extension from when I purchased it)
I just wanted U.S. shoppers to know, that Dwarv may end up being an issue, (for their own orders), and the Ares definitely is...
The Ares has a new scheduled ship date of 8/12, and the Dwarv is still sitting at 8/10....
I'm willing to give the Dwarv (the one with all the inserts) until the 10th since this is DHL shipping, but I'm not willing to go beyond that. If the Ares isn't in on the 10th with the Dwarv, then I'm removing it from my order...
And if they extend that Dwarv any longer, then it's getting booted too
The Tripod, The Nibiru, and the X is all ready to ship, with the Brunhilde not going to be ready until the 6th now (an extension from when I purchased it)
I just wanted U.S. shoppers to know, that Dwarv may end up being an issue, (for their own orders), and the Ares definitely is...
... there is an option that will give you the flavor and the exact AF you seek, guaranteed. Similar threads
- Locked
