Terminator/Nautilus/Choddy/Oddy Clone Pics, Tip,Tricks and Quirks

[Technonut]

I'm on a list for one more item... ( I mean it... I swear it, I.. I.. errr.. I'll try.. ) Couldn't help myself on this one:

Eden Mods - Rose Atomizer

They should be widely available after the first run...

 

[dwcraig1]

@ Innocuous, Vapor Freak also has parts for Terminator/nautilus but of coarse they are in Germany. Also Oddy parts work as well when you can get them.
Perhaps consider putting the Ithaka clone "Hercules" also in your list of possible next atties.

 

[villarino1k]

Does anyone have the Euforia? I swear I can't get this to stop leaking or gurgle. I've tried many times without any success. Really frustrating especially thinking about how much juice I've wasted trying to get this thing to work properly. The set up is exactly the same as a term c which I don't have any problems with either leaks or gurgling. I can keep the juice control completely closed and still be able to use it without the wick drying up. Slightly opened, it'll start to gurgling more and ill set it down for a bit and theirs juice inside my mods 510 connector.

Btw, I don't keep the negative wire trapped between the knurled ring and base. I simply make sure I keep it tucked behind the silica wick touching the metal.

Any help would be greatly appreciated

 

[UA72Riddle]

Does anyone have the Euforia? I swear I can't get this to stop leaking or gurgle. I've tried many times without any success. Really frustrating especially thinking about how much juice I've wasted trying to get this thing to work properly. The set up is exactly the same as a term c which I don't have any problems with either leaks or gurgling. I can keep the juice control completely closed and still be able to use it without the wick drying up. Slightly opened, it'll start to gurgling more and ill set it down for a bit and theirs juice inside my mods 510 connector.

Btw, I don't keep the negative wire trapped between the knurled ring and base. I simply make sure I keep it tucked behind the silica wick touching the metal.

Any help would be greatly appreciated

Again, sounds like air leaking in to the tank somewhere. Start with the oring around the mouthpiece, then work your way down. The oring should be snug on the mouthpiece, but not tight and should slide down fairly easily.

 

[dwcraig1]

I'm on a list for one more item... ( I mean it... I swear it, I.. I.. errr.. I'll try.. ) Couldn't help myself on this one:

Eden Mods - Rose Atomizer

They should be widely available after the first run...

Are there any pictures of the innards around to be seen?

 

[villarino1k]

That's the last thing I have yet to try. I had the same problem with my term c and the o ring fixed it.

So on the term c, the top o ring, is it just a bad type of o ring? Just wondering because isn't the o ring that comes with it the same size that I got which was a 9x2? It's just weird how something like that causes leaks and gurgling.

I also looked it up online, the o ring for the penelope/euforia should be a 8x3 so ill be ordering some online and see if that fixes it.

 

[dwcraig1]

Again, sounds like air leaking in to the tank somewhere. Start with the oring around the mouthpiece, then work your way down. The oring should be snug on the mouthpiece, but not tight and should slide down fairly easily.

Yes this is pretty much the only place, the tank top with it's o-ring. Unlikely but possible the o-ring on the base (bottom of tank)

 

[dwcraig1]

That's the last thing I have yet to try. I had the same problem with my term c and the o ring fixed it.

So on the term c, the top o ring, is it just a bad type of o ring? Just wondering because isn't the o ring that comes with it the same size that I got which was a 9x2? It's just weird how something like that causes leaks and gurgling.

I also looked it up online, the o ring for the penelope/euforia should be a 8x3 so ill be ordering some online and see if that fixes it.

Even though the numbers are the same they are not all created equal (size).
Also if you stretch and roll one out under a magnifying glass you can see the wear on them.
My 9x2's from Grainger seemed just a tad fatter BTW

 

[villarino1k]

Even though the numbers are the same they are not all created equal (size).
Also if you stretch and roll one out under a magnifying glass you can see the wear on them.
My 9x2's from Grainger seemed just a tad fatter BTW

Thanks for clearing that up DW. My new o ring for the term c is slightly fatter as well.

I just ordered some 8x3 for my euforia, I'm really hoping that it solves the leaking/gurgling on this. With the mouthpiece completely closed, it's hitting really well.

 

[dwcraig1]

I just got on the list for the Oddy to Kayfun kit last night, should I be getting a PM on the Polish forum and do they have access to my email address through the forum? I'm not sure if I should be monitoring the site or not.

 

[UA72Riddle]

If I remember right, you should get a pm with payment details when they are close to shipping. I say close, but I think it's been 2 weeks or so since i paid and I haven't received a shipping notice yet.

 

[tagster]

If I remember right, you should get a pm with payment details when they are close to shipping. I say close, but I think it's been 2 weeks or so since i paid and I haven't received a shipping notice yet.

Same here. Calpis got tracking and as of last night the package was in New York.

 

[dwcraig1]

So I guess I need to check the polish forum at least daily then

 

[UA72Riddle]

Yeah, keep up with your pms there. Mine sent an email letting me know I got a pm.

 

[tagster]

So I guess I need to check the polish forum at least daily then

Yes, just make sure to configure your forum account to email notification for PM's.

 

[Technonut]

Are there any pictures of the innards around to be seen?

From what I gather, the makers are letting out full details of the internal design slowly.. The prototypes are currently being machined. When completed, (hopefully in a few weeks) all info will be out, and vids of the Rose in operation will be posted. Then, the prototypes will be sent to reviewers. The folks on the list who are satisfied with everything seen will then pay a 50% deposit on their order until the rest are completed. If this design does everything it's supposed to, it will be one helluva RBA.

I especially like the ability to rebuild without having to empty the tank, and the choice of using a ceramic cup or not.

 

[st0nedpenguin]

I looked at that one and the rebuild without draining tank seemed like a great idea until I wondered to myself how often I feel a need to rebuild with a full tank.

The answer turned out to be not very often.

 

[dragon_ch]

You can do it with Kanger T3,Evod and Protank...of course they do not have juice and air flow control.

 

[XfooYen]

I just got on the list for the Oddy to Kayfun kit last night, should I be getting a PM on the Polish forum and do they have access to my email address through the forum? I'm not sure if I should be monitoring the site or not.

Make sure you have listed your email address in the forum settings and allow members to contact you. I believe vochu will email or PM you when your number is up to pay. It's a good idea to keep up on the threads. There is a thread for the list and one for discussion and announcements. Watch them both. I'm #194 on the list. Added myself a few weeks ago. This is going to be slow moving for sure.

 

[upsetter21]

I go right ahead and unscrew the base off the Terminator when it's full of juice. I just orient up side down and keep the JF tight until the base is off. Then I unscrew the MP leaving it in the top portion's o-ring. I've had to repair coils mid-tank after my MP caught a wild-hair from the wick and pulled my coil out of shape.