Actually I read that wrongYes, the are ... but they do like to throw that flavor out.
- Status
Well, all except for that Tobeco oddy.
The Term-C and the Hercules are the only tank atties I use any more.
Well, all except for that Tobeco oddy.
Tobeco Oddy actually tastes great ... IF you can manage to fill it without spilling a mil of juice all over your lap because of its STUPID ONE PIECE CAP!
(sorry, I'm venting)
I have the Herc too and I LOVE it.
3 mm works great if you don't wick the channels and cut it about flush with ceramic. If you feel You need wick down channels Just take 2 strands of it down channels max.
This is my best cotton set up so far, (I only have 32 available) 1/16 micro of 32 @ ~3 ohms, 1/16 cotton wick down channels. I have a separate piece in the lower part and the coil wick down to the negative ring. This mini micro preforms well and almost doubled my battery life. From 275 puffs to about 450. Must be the small amount of wire because other 3+ohm setups never lasted as long ever. Cotton density is such that when help up to light you can see through most of it with some dark spots.
1/16 nail
Lightly tuft the cotton up so its not pinched and almost fills the top
1/16 nail
Lightly tuft the cotton up so its not pinched and almost fills the top
Last edited:
I guess I should have said I'm using a Term V2. I'm only having wicking issues with thick VG juice I can run about 8 watts before it starts falling off but this juice begs for more heat for the flavour to really come out. I've tried the wick cut off at the channels, it doesn't seem to help much. I've also tried 2mm silica doubled up and one cut the channels, this seems to work really good with the thinner juices, but again my thicker ones not so much.
Holy cow I loosened the draw on my oddity and wow! Like a totally different device. If you like an airy draw . The wicking is really improved and its vaporizing a lot better.(84%vg, 10% water, 6% flavor)I tripled the size of the slots on my mod and 510 with a dremel and also the two side holes on the oddity 510. Wow this is what I'm talking about. It's a totally different vape lots of popping now and just busting out vapor effortlessly. I'm not sure how its all the sudden popping like a dual coil carto even when Im not pulling on it. All I did was open the air flow. If you don't want to enlarge the slots on Your mod you can make the 510 holes bigger or drill another. I just used the cutoff wheel to add a slot to them so Air could get to the air intake easier since I really opened up my mod.
I saw another guy post this up and he was right. Only Difference was he slotted the base of the oddity instead, like the protank Base, you can make some wide deep slots on the base instead.
This is the vape I was looking for. A tight draw really effects performance. This is hitting like a dual coil carto if you liked that.
Mod at your own risk, start small, you can always take More off.
I saw another guy post this up and he was right. Only Difference was he slotted the base of the oddity instead, like the protank Base, you can make some wide deep slots on the base instead.
This is the vape I was looking for. A tight draw really effects performance. This is hitting like a dual coil carto if you liked that.
Mod at your own risk, start small, you can always take More off.
Last edited:
How in the world? You need the Legal Vape 4000, LOL.
Try a .4 ohm dual coil out and you'll understand where all the juice goes lol. Even when I'm not vaping sub ohm I'll still go through nearly as much because my mod never leaves my hand unless absolutely necessary.
Oh man my life got so much easier yesterday
Tell me about it ... I built one a few weeks ago, can't live without it! Even Protank heads are better off with NR-R-NR as you don't overheat the silicone insulator that way.
Tell me about it ... I built one a few weeks ago, can't live without it! Even Protank heads are better off with NR-R-NR as you don't overheat the silicone insulator that way.
Yeah I can finally rebuild by evod heads, not that I use them often. I just could never get the silicone not to heat up. I could have done it before but twisting wires was way too much effort for an evod. I think I'm gonna build an evod head with micro coil and cotton and see what happens.
It will rock, trust me ... amazing what these little BCC's can do with a good micro coil in them.
Can one, or some, of you term-c pros do me a huge favor and lady on your back and vape the term-c totally upside down for a bit and tell me if you get some juice in your mouth?
Is happening with mine and I'm trying to find out if I'm doing something wrong or if this is just not the device for my wife.
Or... Just tell me straight up if this is not the atty for one that is on their back for extended times.
I have other types on the way. I just don't want to give up on this unless I know it's not me setting it up wrong. I've tried many different builds. Thanks
Is happening with mine and I'm trying to find out if I'm doing something wrong or if this is just not the device for my wife.
Or... Just tell me straight up if this is not the atty for one that is on their back for extended times.
I have other types on the way. I just don't want to give up on this unless I know it's not me setting it up wrong. I've tried many different builds. Thanks
I usually vape horizontal, (the whole device), and inverted WILL work, but the condensation and whatnot is supposed to fall into the cup, etc.
I'd recommend this gooseneck gizmo, as I hear others rave about it.
I'd recommend this gooseneck gizmo, as I hear others rave about it.
You'll potentially have juice feed issues if it's upside down for an extended period; feed's near the tank base.
Thanks guys. Yep. I know I need to tell her to upright it now and then to wet the wick. Mainly want to know if I should ever be getting juice in the mouthpiece if I did it right and if all seals are working
I get juice in my mouth also if i'm vaping in bed. I don't think its avoidable. She can try and close the juice control a bit and see if that helps. Surprisingly I get less juice in my mouth if i'm using a Genesis style. I would have thought otherwise
Oh man my life got so much easier yesterday
Did you build this or buy? Looking to get my hands on one or find a thread that shows how to build one.
- Status
Similar threads
- Locked
