- Status
Yes, hands down the best clone. The gg base works best for the term, but for other atties, the MKB adapter is what you want....or the stealth cap for it.
I am using the same 9 x 2 mm orings as you are
and it's so tight that if I leave it sitting for a while, I can't adjust the juice control without tipping the whole thing upside down to get some juice to the oring to lube it up. Maybe try a different oring? I also make sure that locking ring is screwed down tight, it can come loose from opening the mouthpiece juice control. Dude, let's get you back to happy Termland.510 pin. i open it up not even a half turn. itll slowly leak out. full turn, it leaks out a little quicker.
glad someones enjoying their term haha. i was so surprised that it started leaking again! i had 2 new coils set up. 2 new o rings and both had the same problem. its like being back to when i first got my terms.I am using the same 9 x 2 mm orings as you are
the top is so tight on mine too. ive been building it exactly how i used to and it started giving me problems again, this time, im really stumped.
but like i said, i also have the short mouthpiece so i took off the long one and took off one tank and started using it in short mode. NO LEAKS! mind you, its the same coil.
Last edited:
im about ready to ditch this term c in complete mode.
DW, i PM'ed you to see if you have any problems with that team rampage tank you got. Leaks or any gurgling?
such a trip that it doesnt give me any problems in short mode
DW, i PM'ed you to see if you have any problems with that team rampage tank you got. Leaks or any gurgling?
such a trip that it doesnt give me any problems in short mode
Check for fine cracks in the plastic tank threading. That tank is fairly brittle and can fracture along the threading pretty easily. That could ruin the vacuum and make the tank leak.
from tapatalk
I have the cheapie clone but check to see if it's just over-wicking. When I only use one wick mind leaks a ton. Do you use a single strand of silica or do you double it up? How many mm's is the silica you're using?
Thanks. I also have kayfun coversion kit and ithaka clone on the way. Anything different between setting up conversion kit for Term-C and Ithaka?
same......maybe except for:
Ithaka tank is around 23 mm tall and Term-C's two sections of tanks is 35 mm so you'll have more mouthpiece sticking out, that's it.
I just might be wrong about this, if there is something different to fit it into Ithaka it would be adding a taller tank.
On the upper assembly, Term-C, the place where the mouthpiece goes from approx. 7 mm back to 9 mm is about the same location on Ithaka's mouthpiece where the stop is located.
The chamber on the Kayfun kit extends much farther so the tank top wouldn't fit on.
So from what I see an additional tank section would have to be added or use two Term tank sections.
Also Ithaka's basic feeder is 3 times taller the the locking ring for Term, I almost missed that.
Perhaps when you specify that it's for Ithaka, a tank section is included with the kit, does anyone know about this?????
Ithaka tank is around 23 mm tall and Term-C's two sections of tanks is 35 mm so you'll have more mouthpiece sticking out, that's it.
I just might be wrong about this, if there is something different to fit it into Ithaka it would be adding a taller tank.
On the upper assembly, Term-C, the place where the mouthpiece goes from approx. 7 mm back to 9 mm is about the same location on Ithaka's mouthpiece where the stop is located.
The chamber on the Kayfun kit extends much farther so the tank top wouldn't fit on.
So from what I see an additional tank section would have to be added or use two Term tank sections.
Also Ithaka's basic feeder is 3 times taller the the locking ring for Term, I almost missed that.
Perhaps when you specify that it's for Ithaka, a tank section is included with the kit, does anyone know about this?????
Last edited:
Don't know if tanks are included for the Ithaka, but I do know Vochu said tank height must be 40mm...though I'm not sure what or where he is measuring.
I really don't think it will work with standard Ithaka. Mine will be here today, out for delivery. I'll check it out when it gets here.
I really don't think it will work with standard Ithaka. Mine will be here today, out for delivery. I'll check it out when it gets here.
I would suspect he spoke of the combined height of base-in-tank and 'chimney', (as some call it).
No, not overall height, but minimum required height is what he stated. But now I question that with dw saying the term is 35mm.
Opps, my mistake it's 34 mm, I'm measuring from seam to seam on the outside of the Term
Looks like 40 mm from the bottom tank o-ring to the top of the tank top
We know it fits Term-C so figure from there
Last edited:
Ok, so 40 is right, and he is measuring the same way you did. Mine should be here within the hour and we'll have a definite answer to if it will fit.
There would not be much left, the area on the outside is super thin
I posted these in the Hercules thread, but I'll quote them here too...
I received my Hercules this morning... Same great quality as the Terminator, but it appears a thinner gauge SS was used in the Herc.. I'm not certain if this was Imeo's design for weight reduction, or RH's? Nevertheless, it has smooth threading, is well-machined, and is a quality piece for certain.
I still need to get around to setting this bad-boy up with dual-coils. I'm going to use 2 of Stormy's 2.4 ohm ready-wires and some 3mm German silica to start off with...
Are you using the 510 base? I'm using the GGTS base on my MKB-TS. The center pin is solid, and concerning the draw, I can open it up pretty airy using the AFC on the MKB-TS if I want to. I prefer a "mid" draw, and it's great for me.
Setup on my Herc wasn't bad at all.. 1.2 ohm (2x 2.4 ohm ready-wires) dual coils are pumping-out some warm, flavorful vapor..One must make damn sure the top cap is VERY tight. I had slight gurgling until I thought to really crank down on it. I'm using my DIY 70/30 Hangsen Highway tobacco, and only have the juice control cracked open a little with no dry hits yet.
- Status
Similar threads
- Locked
