A Magma should fit that profile.
Tootle Puffers, Redux (The Sequel)
- Thread starter Katdarling
- Start date
- th_trl_thread_readers 0
- Status
A Magma should fit that profile.
A lot of people like the Magma Magma Atomizer / Clone by Infinite CLT / Magma RDA
Not sure if it meets all your needs though..
Yes like the Achilles or the Chels MiniDrip, however the MiniDrip is not in stock AChilles clone not on stock and the genuine Achilles is very much not frugal about 230 CDN.. hmmm nope
Vaporrange has the Tobeco on sale for $9.95:
VaporRange.com | Your Online Vape Store. Free US shippping.
VaporRange.com | Your Online Vape Store. Free US shippping.
I have a Magma it is a little bed wetter.
Other than that I like it.I think what happens is vapor condenses on the top cap run down across the deck and out the air intake. I may dremel it into submission.
Kayfun dripper, hmm what is this strange beast...
Hi ho hi ho its off to google I go
and ty
Hmmm. Now that's an idea. I got a few bell caps from FT before I realized that the regular chimneys won't fit in them. They could be used that way. Just take out the chimney and chamber, then screw on the bell cap and drip.
Exactly
Written on 21st Century papyrus
Written on 21st Century papyrus
I just tried it and IT WORKS! And it's a lot less messy than my Magma. I can just pull off the drip tip, stick in my needle top bottle, and drip right on the coil. No need to take the cap off at all.
@Boden, you're brilliant!
Cupcakes?? That's the best ya got?
We have free humps. By Andria.
Wait, WhAAAAAAAAAAAAAT?????????
Mine was a tad more complex than that. I modified the KFL topcap so it fits over the coil and has top airflow.I just tried it and IT WORKS! And it's a lot less messy than my Magma. I can just pull off the drip tip, stick in my needle top bottle, and drip right on the coil. No need to take the cap off at all.
@Boden, you're brilliant!
Modified on left
Drilled some holes
Last edited:
Cupcakes?? That's the best ya got?
We have free humps. By Andria.
The only kind I can handle anymore.
Andria
@gt_1955, @MikeyConti, @Eric Auer - Thank you gents! That's kind of what I was hoping to hear. I run kanthal about 0.7-1.8ish, so a 0.6 SS coil wouldn't be hideous, and if I can get about 1.3-1.4, that would nice on the high end.....
Y'all got me thinkin' now....... Although, I do use kanthal in my PT2 heads - that's just EASY for me.... I guess I'm looking more for my other tanks/RDAs.....
Appreciate the insight
Y'all got me thinkin' now....... Although, I do use kanthal in my PT2 heads - that's just EASY for me.... I guess I'm looking more for my other tanks/RDAs.....
Appreciate the insight
The things I learn on ECF. I'm not only a tootle puffer (Provari 2.0 and 2.5 sporting z-atty-pros), I'm a tootle puffin' ole fartress. Do I get a cookie or sumptin?
Yeah, but mine only took 30 seconds to build!
In all seriousness, though, it's really amazing what you can do with a little bit of ingenuity. I was ready to throw my Kayfuns in a drawer because they hate me. But I'm getting a nice vape with this one in dripper mode.
Yep we will fax you a cookie. Actually you already got a cookie from ECF
Welcome to our world.
@gt_1955, @MikeyConti, @Eric Auer - Thank you gents! That's kind of what I was hoping to hear. I run kanthal about 0.7-1.8ish, so a 0.6 SS coil wouldn't be hideous, and if I can get about 1.3-1.4, that would nice on the high end.....
Y'all got me thinkin' now....... Although, I do use kanthal in my PT2 heads - that's just EASY for me.... I guess I'm looking more for my other tanks/RDAs.....
Appreciate the insight
According to Steam Engine, though, you would need 13/14 wraps to get a 1.3 ohm coil. That's a lot of wraps for quite a few rta/rdas. I've thought about trying ss wire, but wish it came in smaller gauges. It would be easier to get my target resistances.
- Status
Similar threads
