Bulli A2-T

[eyebrook]

I think the SS are predrilled and the ali you have a choice for it to be drilled or not

 

[Wingapo]

Upgrade kits I believe you have to drill yourself, but the full A2/A2-T/A2-MegaT are predrilled. Silly me doesn't have to worry though because I only ordered the part that doesn't have the hole in it to go with, I guess, my aluminum A2-T wick holder fiddly bit.

 

[lexi60]

Hey guys.
I'm loving my A2, but I'm having trouble with A2T, I can't get the flavor to "shine" I'm getting good flavor. Just not THE flavor.
I'm having no issues with wicking..
Maybe cause the update kit is aluminum?
Any tips?

Sent from my HTC Glacier using Tapatalk

 

[ukeman]

hmmm would ss be hard to drill?

 

[Stownz]

just gotta have good drill bits, the housing is pretty thin.

 

[Wingapo]

Uke, just be sure to tap a nail or something similar to put a slight depression where you want to drill first, so the drill bit won't wander, and then you are golden.

 

[dspin]

Hey thanks AG for posting this. I hate an airy draw like Uke.

Ukeman,,,

You won't like the Bulli.
It's too easy of a draw, based on your comments here, & others I've seen on the ECF.

The air hole could be covered & made tighter, but you wouldn't like it without modification. I don't expect the Mark Infinity to be any different.

Perhaps you could have Bulli reduce the size of your air hole.

 

[Wingapo]

As long as giant tasty flumes of vapor get injected into my lungs I'm a happy camper, no matter how airy the draw. But that's just me.

 

[Dudeman]

The best way to get a nice stuff draw is to get an upgrade kit and use a Dremel with one of the thin cut off wheels instead of drilling. Grind the wheel on something until it's half sized or less, then use that to make your hole. You don't cut through the tube, just deep enough to poke a pin through. It only takes a couple seconds if you use a very small wheel.

I can't use the standard cart tube anymore since doing the upgrades this way.

 

[nicadd]

Upgrade kits I believe you have to drill yourself, but the full A2/A2-T/A2-MegaT are predrilled.

Yep.

Another way of getting a tighter draw is to put the coil in front of the air hole instead of on the other side of the screws, or use two coils.

 

[dspin]

Yep.

Another way of getting a tighter draw is to put the coil in front of the air hole instead of on the other side of the screws, or use two coils.

Thanks for the info Nic, I may get one yet now.

 

[Wingapo]

Go for it Dspin, you deserve one as a reward for all your patient waiting.

 

[dspin]

Your right Wing - I'm going to order when they are avail again.

 

[badkarmaiii]

I don't have a Bulli, yet, but have been using an eGo-T Type B along with my ProVari.
One thing that I've learned is that a harder draw sucks juice past the tank seal, creating an even harder draw and, eventually, problematic leakage.
Since these are targeted at handy folks, maybe Cetin could drill them with the smallest hole possible. It's much easier to enlarge an existing hole than drill a new one through a curved surface.
Just a thought...

Thanks,
Lee

 

[Killjoy1]

I think I'll have to snag a Bulli when they're available again. I do like the tanks and have heard the A2-T gives better flavor, which is my biggest complaint about the ego tanks.

I probably shouldn't considering how much I've been spending on vaping lately, but I guess I just suffer from "ooh, shiny!" syndrome . . .

 

[Wingapo]

Killjoy you're in good company here, we all suffer from the same affliction as well. The A2's are really fine attys and they do have me seriously considering quitting dealing with most others for good. Just today I had one of them fancy schmancy IKV's die after only two days and it sent me running back to the one I know works, the A2.

 

[ainako]

As long as giant tasty flumes of vapor get injected into my lungs I'm a happy camper, no matter how airy the draw. But that's just me.

My thoughts completely!

 

[Wingapo]

Come on customs it's time to release our A2's!

 

[ainako]

Has he shipped them already? I never got a notification. This bad mama would go nicely with my p+500

 

[Wingapo]

Yeah this sweetheart's topping of my P+18500 as well. I actually don't know if they've shipped I hear they often don't send shipping notices. I'm just going on the belief that mine is going to clear customs and be on its merry way to me tomorrow.