Bulli A2-T
- Thread starter BigBulli
- Start date
- th_trl_thread_readers 0
- Status
Wing, there appears to be one slight flaw in this: I believe the necessary air hole is drilled in the spike section of the A-2T and A-2TM Bullis, not in the upper tank section.
You could probably drill a hole in that upper section in order to make it work as a dripper without using the spike section, but then you would have one too many holes if you wanted to use the Bulli as a tank atty again.
That's what rubber bands, o-rings or tape are for. Or, you could dremel or file a channel along the side of the drip tip to provide an air channel. We've come this far so I'm sure if we put all our heads together again we'll figure out this slight setback as well.
See I told youz all we were a bunch of freakin' geniuses! Almighty has proven once again you can trust in him.
Also it looks like the only US ego drip tip supplier that has both the type A and type B drip tips at $1.99 and has $2.99 shipping is Vixen Vapors. So far that's the best deal I could find here in the states.
Also it looks like the only US ego drip tip supplier that has both the type A and type B drip tips at $1.99 and has $2.99 shipping is Vixen Vapors. So far that's the best deal I could find here in the states.
How hard is it to pop it out and how did you go about doing it. I assume it then becomes a A2. I just need to be able to drip also w/a dt
Yeah I heard this as well in an a2-t review where they said the little spike part would come out.
---
I am here: http://maps.google.com/maps?ll=32.588296,-83.663859
Damn it... another 10 days, without the certainty to actually be able to order it...
If anyone is selling one A2 (any version, but if T or TM it's even better), I'll buy it in an heartbeat!
If anyone is selling one A2 (any version, but if T or TM it's even better), I'll buy it in an heartbeat!
Ok now she's wicking inconsistently, anyone else run into problems?
Sent from my DROIDX using Tapatalk
Sent from my DROIDX using Tapatalk
Don't have mine yet but I'm trying to pick up tips along the way until it comes. Seeing how I use 70% vg
---
I am here: http://maps.google.com/maps?ll=32.588044,-83.664175
Lovin the a2 ever since receiving the wick material they sell. Getting really great flavor and perfect airflow using the method of tying the two sides of the wick together so it comes up vertically directly into the cart. Also really good for dripping. I have two of them going, one for dripping (with ss 701 adapter) and the other for use with the cartridge. Am surprised with how well the cartridge really works. For those of u that haven't already, definitely give it a shot! The only issue I have with the bulli (or any rebuildable out at this time) is liquid coming out the airhole from time to time. If only it had some kind of mini trap valve or something that lets air in and not out - THAT would be kewl 
ok so my problem was my coils, apparently I was making coils at to low of an ohm range <1. performing perfectly now! I hope. So check your ohms people!
If the turns of your coil touch it will reduce the resistance by shorting across the touching turns , hope this makes sense
I'm running mine with Mesh as well,,,, and with the tank of course,, one thing I found that I did that is working out nicely that I said a while ago is I wrapped a piece of scotch tape around the unit once, covering the hole,,, then I took a pin and put a small hole where the hole is,,, this stiffens up the draw and also pulls more liquid from the tank to the wick, also stops any excess liquid from running out,,, Running mine pretty dam hard on my Darwin, it's working great !!!
Last edited:
just rolled a piece of ssmesh burned and quenched then wrapped as usual and installed just like you would using the bulli wick. Also using ssmesh in the spike with no wick
- Status
Similar threads
- Locked
- Locked
