Bulli A2-T

[JollyRogers]

juice at the base of the atty? Are you using inhales to prime it and them flooding?

Yea I keep mine short for the T/TM. Coil is arched between the screw posts, but not high up. Wick is just as cetin's video regarding thickness. I use 5 wraps of 32gauge kanthal, resulting in a 1.6Ω coil. Single strand of spike wick, basically the SS wick is barely holding itself in place. Messing with the spike wick is worthwhile... I check mine after a build and make sure it is feeding the coil. If not, I make adjustments... My single strand gets tucked on the non air side of the coil and usually unravels about the coil some.

 

[clyde2801]

Couple of quick things....

1. Used a kick beta with the bulli. Hits consistently every freakin' time. Slight tradeoff in battery life in using up a 18490 versus a 18650, but worth it! Can tune in the wattage or heat for the juice I'm using. My coil making skills (or-let's face it-lack thereof) have become almost irrelevant.

2. Jolly, thanks for helping with my newbie mistake yesterday. Duh.

3. Madvapes sells a Ego mega cart to 510/901 drip tip adapter for $.99. Since the big honkin' rubber tip from the ego mega dual coil cart fits perfectly in my a2-tm tank*, this should give me a good cheap option for drippin' and vapematin' until I can get a downgrade kit.

My hoarding paid off! Huzzah!!!

 

[clyde2801]

Couple of quick things....

1. Used a kick beta with the bulli. Hits consistently every freakin' time. Slight tradeoff in battery life in using up a 18490 versus a 18650, but worth it! Can tune in the wattage or heat for the juice I'm using. My coil making skills (or-let's face it-lack thereof) have become almost irrelevant.

2. Jolly, thanks for helping with my newbie mistake yesterday. Duh.

3. Madvapes sells a Ego mega cart to 510/901 drip tip adapter for $.99. Since the big honkin' rubber tip from the ego mega dual coil cart fits perfectly in my a2-tm tank*, this should give me a good cheap option for drippin' and vapematin' until I can get a downgrade kit.

My hoarding paid off! Huzzah!!!

 

[Domtine]

Hi all,

Had my TM for 2 months now but recently after a needle wick change, my TM is acting strange. the 1st half of the tank vapes fine but when I reach the 2nd half i.e. can't see the juice in the tank when holding upright, it starts to floods the base. I measn literally flood. When I unscrew the base there's juice dripping right off it. I followed the same method as I did previously and there were no problems. Searched through this thread and can't find any related info. So far What I tried to rectify this:

New wick coils
new tanks
new spike coils
used 3 wicks for the spike coils and ended up with 1st half slightly dry and 2nd half flooding just as bad.

All the above didn't work

Anyone has any suggestions?

 

[JollyRogers]

Maybe try raising your ss wick up higher into the spike? Or make a larger/tighter in the spike ss wick? I dunno!

How long is the fiber wick(s) in relation to the base of the air chamber? I cut mine flush...

 

[clyde2801]

Rubber eGo Mega Cartomizer Round Drip Tip Confirmed, this does work perfectly on my a2-tm tank. Therefore, other products SHOULD work as well.


510 Drip Tip Adapter for eGo Mega Dual Coil Cartomizer Couple on the way. Hello, vapemate.....

Black Anodized Drip Tip for the EGO Dual Coil Hard version of no 1. Should work, and in stock.

Silver Drip Tip for the eGo Dual Coil Should also work, but out of stock..natch!

 

[Domtine]

Tighter wick no use. When the juice reaches the 2nd half it starts to flood again. Maybe I'll try making the wick protrud more into the tank

 

[bobbylo]

Hey Clyde,do you know what joye tanks fit on the Bulli A2-TM (type A?) (Type B)

 

[Domtine]

Hey Clyde,do you know what joye tanks fit on the Bulli A2-TM (type A?) (Type B)

A2TM uses type-B tanks. A2T uses type-A tanks

 

[butters73]

ive got a "shipping" question ,is there anyone else that ordered from bulli smoker that had their package reach isc new york n.y. but never update again? everyone i know that ordered " jan 31 2012" has recieved theor shippments,but me. i only live a few hours from isc ny facility,which is why im concerned that im the only one i know that hasnt got theirs.ANY help here would be appreciated.

 

[clyde2801]

Mine took about a week....roughly, once it reached ISC to get to Oklahoma.

 

[bobbylo]

ive got a "shipping" question ,is there anyone else that ordered from bulli smoker that had their package reach isc new york n.y. but never update again? everyone i know that ordered " jan 31 2012" has recieved theor shippments,but me. i only live a few hours from isc ny facility,which is why im concerned that im the only one i know that hasnt got theirs.ANY help here would be appreciated.

Yeah,mine was there about 9 days.I just recieved it yeasterday,although there was a problem,and they could'nt find the package.Turns out my address was written a little different then it should of been.IE: my street on top,then my name,then the street number,the the zipcode,followed by the city and state.Those idiots at the post office could'nt figure it out.I had to go there twice.......Anyhow,
My package did'nt update till it hit atlanta,about 9 days after it went in ISC,NY

Delivered
February 21, 2012, 3:16 pm
DACULA, GA 30019
Registered Mail™
Arrival at Unit
February 20, 2012, 1:34 pm
DACULA, GA 30019
Processed through USPS Sort Facility
February 18, 2012, 11:03 pm
ATLANTA, GA 30320
Depart USPS Sort Facility
February 18, 2012
ATLANTA, GA 30369
Processed through USPS Sort Facility
February 18, 2012, 1:12 am
ATLANTA, GA 30369
Processed Through Sort Facility
February 09, 2012, 1:39 pm
ISC NEW YORK NY(USPS)
Origin Post is Preparing Shipment
Processed Through Sort Facility
February 09, 2012, 2:19 am
FRANKFURT AM MAIN, GERMANY
Acceptance
February 07, 2012, 4:58 pm
GERMANY

 

[bobbylo]

A2TM uses type-B tanks. A2T uses type-A tanks

Thanks Karl...

 

[butters73]

yeah,thanks Karl,I STILL HAVENT RECIEVED MY BULLI A2-T YET!!! im soo frustrated,its read "processed through isc n.y. " since feb 9. should i be as worried as i am????

 

[clyde2801]

Update on the mad vapes adapter....

It does work, kind of. Fits, but is a tiny bit loose, and no time in the next couple of days to run to the hardware store for o-ring shopping.
Don't like it as is for the vape mate on the bulli a2-tm tank, just a bit too wobbly. But it is acceptable for putting a standard 510 drip tip on the top of my TM tank.

 

[MediocreTrombonist]

yeah,thanks Karl,I STILL HAVENT RECIEVED MY BULLI A2-T YET!!! im soo frustrated,its read "processed through isc n.y. " since feb 9. should i be as worried as i am????

Hmm that is a very long time. Should you be worried? I don't know enough to know, but I would look for ways to inquire about it. I don't know what you can do about it though... Sorry to hear about your situation.

 

[urquidezj]

No brass period. And register as vendor before u get slammed.

 

[bobbylo]

Register as vender where? and what do you mean i might get slammed?LOL,don't like the idea of brass huh?I figured some people have brass end pieces on there battery mods,and it might look nice..But thanks for the input.

 

[BJ43]

Register as vender where? and what do you mean i might get slammed?LOL,don't like the idea of brass huh?I figured some people have brass end pieces on there battery mods,and it might look nice..But thanks for the input.

Slammed = banned

No talk here about production or sale allowed here, this is totally amateur to share ideas, the professionals have their thread;
Modder/Accessories Supplier Forum

 

[NotoriousJoe]

ive got a "shipping" question ,is there anyone else that ordered from bulli smoker that had their package reach isc new york n.y. but never update again? everyone i know that ordered " jan 31 2012" has recieved theor shippments,but me. i only live a few hours from isc ny facility,which is why im concerned that im the only one i know that hasnt got theirs.ANY help here would be appreciated.

Hey I have the same exact problem. I ordered some supplies on the 28th of January and it's been in NYC since February 9th. I called the USPS and apparently there's a customs in new York that I thought was odd. Didn't know we had a customs in the us.

They told me only thing I could do was wait. So ....... Love my bulli wick and I ordered way in advanced so I wouldn't run out , now I'm having to scrap pieces of wick together. It's driving me crazy!


---
I am here: http://tapatalk.com/map.php?uvznav