Bulli A2-T

[MXBNW]

I just put a peace of scotch tape over 1/2 the air hole and its working just fine Loving it now with the 701 cart I will drop my DT set on it latter today to see how it work that way. I will be drilling a smaller hole in my new one for sure.

I think out of all the rebuildable attys I have tried this is by fare the best I have found for me hand what I am looking for from a rebildable atty.

Now if some one would come out with an atty like this but with a adjustable air flow I would be set. Oh and one that would work on my bottom-feed mods.

 

[jimbalny]

Man, the wick I got with the a2 I bought from classifieds just dont taste good for some reason. Its a braided fiberglass kinda deal, bigger than the stuff cetin sells. Also tried ceramic wick, no go. The best success ive had so far (aside from the original wick that it comes with, which im out of) was with ss mesh with a channel inside it for juice. Tried everything, washing, preburning. Making a coil is getting easier and quicker, just dont have the right material yet. Hopefully I get the stuff from cetin soon - but its pretty much a mystery as to when.

Aside from the stuff that comes with the a2, what have u guys tried that vapes real clean?

 

[Wingapo]

It's beginning to look like boil the heck out of everything to make coils is going to be rule #1. It's not too bad with very flavorful juices but with the subtle flavors the wick/coils seem to make the juices taste stale and so far for some reason the TH on a low TH juice starts going through the roof.

 

[Stownz]

I've definately been having issues with taste differences between both my A2 and iatty. I don't think its the wick, I think its the wire.

 

[Wingapo]

Stownz, what wire would you recommend to use for each?

 

[ED-209]

You can defeat that for most things, I have a bunch of different adapter combos, and use my bulli A2-T on a darwin almost exclusively. Other lengths of adapters let DCA306s close, and if its really wide, slap on the gooseneck.

Actually, no, tanky sized objects usually end up on the Provari

Were you able to get the Bulli more consistent since your video review?

I noticed on the review you said the iAtty was overall the best when it came to consistency so curious how you were able to achieve better results?

Tanks and it was a great review and demonstration as I always enjoy how thorough your reviews are.

 

[mergryphon]

Were you able to get the Bulli more consistent since your video review?

Yes, by taking the two strands of wicking out of the SS mesh, it wicks much better for how I use it. I now use it regularly.

I still prefer the iAtty but those tend to stay home or in the car. A2 on the darwin goes out and about in my pocket, just need a small bottle of juice and a tissue along for refilling the tank.

And thank you, hope they are helpful.

 

[mwa102464]

Ive now got mine set up just like my G-Tanks and having great success with this way ! I also like using it the way it was intended to be used as well. When it comes to mesh, no matter what I'm using it on, I boil it for about 3-5 min. Then I heat it 4-5 times until it glows orange and then dip it back in the boiling water after each time. I then put VG on the mesh and cook that dipping it in the boiling water after each time. The the last 2 times I even drip the juice I'm going to run on it and then dip back in the boiling water. This seems to oxidize the mesh just right, may seem like a lot but it does the job. I also drill a small start hole, not a hole but just a small slot to hold the mesh in place in between the 2 post. Have the mesh going up into the Ego Mega tank cart, My set up is running super like this and I also put a bigger screw post on one side.

Also running at 1.7ohms

 

[ED-209]

Thanks for the info and help. I've been trying to get one and I am even trying to trade my iAtty for a classic but looks like I'll end up just buying a new one and selling my iAtty.

 

[quendelyn]

I prefer the wick that Cetin supplies. But I do use the wick from nhaler when I run low. I take 3 small strands and make a tiny braid. This works well. The taste is fine. Also the amount supplied is a good bundle and should last a year, the way I use it.
Now a question for anyone who has the update kit in stainless steel. How much does it weight? I ordered mine in stainless, but it is so dull and gray, I'm thinking it's aluminum.

 

[jimbalny]

That is normal color for stainless that's not polished, aluminum would actually be lighter in color if I am correct.

Mwa: im not sure I follow what you mean by slot to hold the mesh up. Can u show a pic or quick diagram? Very curious. Also, u put an all new post on the positive side?

 

[mwa102464]

@ Jimbalny,,, not sure what you don't understand Jim,,,, it's pretty easy and self explanatory,, I didn't drill a hole in between the center post but I drilled a starter of a hole ( not all the way ) and yes I replaced the screw with a bigger one and I added a 2nd brass washer too, this way my post sits up higher.

 

[BigBulli]

@ Jimbalny,,, not sure what you don't understand Jim,,,, it's pretty easy and self explanatory,, I didn't drill a hole in between the center post but I drilled a starter of a hole ( not all the way ) and yes I replaced the screw with a bigger one and I added a 2nd brass washer too, this way my post sits up higher.

I recomend just switching the screws around like I explained in this thread. Why I don't recomend longer screws is the risk of short circuits if you use a screw that touches the bottom of the piercing plate. Also you will add more resistance. The piercing plate or carto cap will hold the mesh in place no need to do what you did.

Sent from my HTC Glacier using Tapatalk

 

[jimbalny]

@ Jimbalny,,, not sure what you don't understand Jim,,,, it's pretty easy and self explanatory,, I didn't drill a hole in between the center post but I drilled a starter of a hole ( not all the way ) and yes I replaced the screw with a bigger one and I added a 2nd brass washer too, this way my post sits up higher.

I'm an idiot, must have read it wrong. Makes perfect sense

 

[dogpound9219]

cant wait to order them

 

[ainako]

the new precise plus from super t and the upcoming mega-t version of this has got me contemplating on selling both my gg's and both of my iatties.

 

[Wingapo]

that's some serious excitement you have there Ainako. When did Dave post the Precise Plus? Geez I just got my P16 a few days ago, now I've gotta have me one of these. Guess I might have to sell my GG and iAtty too. NO WAY!

 

[ainako]

http://www.e-cigarette-forum.com/fo...24381-new-mods-preciseplus-18500-18350-a.html
I picked up a P+18500, before i bought my first gg which was the steel one. I STRONGLY considered buying a precise. But opted out for the GG for the locking button. Since then I bought another ssggts and the fuse upgrade for both them and 2 iatty. But one iatty has gone rogue on me and decided to leak on me. I'm going to send it back to Imeo to see if he can sort it out, he offered to do so and that is a great testament to his great character and passion for GG. I have always like the precise line and the fact it is all steel for a great price, and now it has a locking button! All I know is that if it plays nice with the iatty I may keep the iatty twins. But I find myself not really in need of such a large tank, plus it can be quite messy and cumbersome to clean the coil, whereas with the bulli mega its easy peasy. GAH!!! I used to be addicted to nicotine when I smoked, but since I have been vaping it has become an addicting hobby! Much excitement in the world of vaping!

 

[Wingapo]

I just got the P16 I ordered over 2 months ago last friday and now these new P18500's and P18350's come out. And of course I spent the money for one or both on a new SS GGTS and iAtty too. Luckily my P16 has the new contacts and finish but dagglynabbit I want a P18500 too! Dave said the new P16's juice well is the same size and depth as the P18500 and P18350 and I am sad to say that the only way my iAtty works with the P16 is with a 510 to 510 adapter because the 510 on the iAtty doesn't make contact with the connection pin on the P16 until it is screwed all the way on cutting off all airflow. But if you don't mind the 510 to 510 adapter then it works on the P16 and probably works the same on the P18500 and P18350 as well. I love the Bulli A2 so far it's the easiest rebuildable to use. My iAtty leaks a bit too but not so much that I'd want to send it to Imeo because I'm really liking it too much to part with it after waiting so long to get up the nerve to try one. Vaping is way more addictive than smoking ever was. I vape three times more than I smoked and so far it would have been a whole lot cheaper to stick with smoking too. There are just so many ways to get so many nicotine infused flavors deep into my lungs. I'm even liking a few tobacco juices much more than I ever liked the real thing. Yes, much excitement in the world of vaping!

 

[ainako]

Sad to know about the iatty on the P16, I may have to sell them after all =/. I will wait for the mega-t bulli to come about and see how that does before I make a firm decision to sell my gg twins though. And like you Wingapo, I have recently gotten addicted to tobacco flavors as well, primevaping has the best I have tried yet.