- Status
Tart raspberry cantaloupe sounds delicious....is it DIY or vendor juice. If DIY care to share the recipe.
Tanks here when they have them
Odysseus Clear Tank - Avid Vaper
My broken on was from Silicawicks, the one that came with the Terminator and the one that I got from Rampage is still going strong.
Odysseus Clear Tank - Avid Vaper
My broken on was from Silicawicks, the one that came with the Terminator and the one that I got from Rampage is still going strong.
Its DIY, really simple and taste like now-n-laters to me.
All TFA flavorings
10% cantaloupe
8% SWEET raspberry
2% ripe banana
1drop/5ml sour (tiny bulb dropper from TFA)
Sometimes I add 1-2% EM
I've been on a cantaloupe kick lately and have been using as a foundation flavor in all my fruit mixes lately
Last edited:
The Terminators are slowly taking over all of my mods...really liking them. I still have two more to set up.
That's me you are talking about, The $250 is in Singapore dollars not USD, coupled with the WU price that we have to pay to get it to our country and the exorbitant shipping cost that's really not that unreasonable
It sucked not to be in US but that's not my choice. BTW, the avatar is my GF
That's me you are talking about, The $250 is in Singapore dollars not USD, coupled with the WU price that we have to pay to get it to our country and the exorbitant shipping cost that's really not that unreasonable
It sucked not to be in US but that's not my choice. BTW, the avatar is my GF
Aww, I see now. How much would it be in US money?
:: sent from android with tapatalk ::
just a couple dollars under $200 US, like $197 and some cahange
Not too much. I'd say it's ok, affordable.
Alvin, that looks top notch! What type of ring are you using to get that flush of a mount? I have the hippo and twins on my mini, but the hippo causes a pretty good gap..
Hello,
my nautilus v2 long leave liquid drops on the battery thread. center pin is 1 mm outside the 510 threadin. 3mm wick, negative wire is inside the ring/base for not leaking.
One concern, center pin seems a bit bend when not build. can that cause an issue?
any ideas please?
my nautilus v2 long leave liquid drops on the battery thread. center pin is 1 mm outside the 510 threadin. 3mm wick, negative wire is inside the ring/base for not leaking.
One concern, center pin seems a bit bend when not build. can that cause an issue?
any ideas please?
Follow this procedure for adjusting the center pin into the base but DON'T trap the ground wire under the ring, instead wrap it around the wick below where the ring will end up when locked so the NR makes contact to the base threads.
As long as the post isn't shorted it should be no problem, just make sure the mouthpiece is centered and the mouthpiece collar is really tight.
Last edited:
Thank you for your reply dwcraig1!
I did as instructed but i still see "moisture" on the battery pin from the very first puffs
as o note, now the center pole is barely visible outside the 510 thread.
it drives me crazy because i really like it's whole concept and i took this since i couldn't find the original.
I wonder what i do wrong.
i have no leaks while filling the long mode with the negative NR wire trick. at least for a couple of minutes it takes to fill.
also inside the center pin all seem clear.
do i have to try a turn at a time till i find what's best position for the center pin when screwing it's base? i run out of ideas.
inside the ceramic there is an o-ring and it's the only thing i don't screw tight.
I did as instructed but i still see "moisture" on the battery pin from the very first puffs
as o note, now the center pole is barely visible outside the 510 thread.
it drives me crazy because i really like it's whole concept and i took this since i couldn't find the original.
I wonder what i do wrong.
i have no leaks while filling the long mode with the negative NR wire trick. at least for a couple of minutes it takes to fill.
also inside the center pin all seem clear.
do i have to try a turn at a time till i find what's best position for the center pin when screwing it's base? i run out of ideas.
inside the ceramic there is an o-ring and it's the only thing i don't screw tight.
Last edited:
@ ckouk, perhaps while filling with the tank open is when your getting your wet spot, does it stop after initial use.
With mouthpiece closed gently blow threw the mouthpiece to remove any liquid in the center post and see if it still does it.
This type of atomizer will always leave the battery post wet but it should be only slightly wet.
The base of the Terminator should sit securely on the crown of the 510 connection (and not because it's over tightened) it should be on there real solid like. If the Term's center pin is flush or just a fuzz inside sounds about right.
With mouthpiece closed gently blow threw the mouthpiece to remove any liquid in the center post and see if it still does it.
This type of atomizer will always leave the battery post wet but it should be only slightly wet.
The base of the Terminator should sit securely on the crown of the 510 connection (and not because it's over tightened) it should be on there real solid like. If the Term's center pin is flush or just a fuzz inside sounds about right.
Hello all,
i just place an order at stormy for the Terminator V2, large. I have a question, quich is down the line, I want a large capacity, can I buy the after market clear tank and just add on? Or should I buy another Terminator C V2?
Thanks in advance.
i just place an order at stormy for the Terminator V2, large. I have a question, quich is down the line, I want a large capacity, can I buy the after market clear tank and just add on? Or should I buy another Terminator C V2?
Thanks in advance.
- Status
Similar threads
- Locked
