Just redid mine this morning, switched from a single coil / dual wick to a dual coil / dual wick X config, with a small piece of silica sitting under the top coil. So far it seems to be doing pretty well.
- Status
Just redid mine this morning, switched from a single coil / dual wick to a dual coil / dual wick X config, with a small piece of silica sitting under the top coil. So far it seems to be doing pretty well.
Funny you should post this cause I thought the draw was alot tighter than my ody was, I ended up drilling it out with a 1/16th drill bit and it is way better now.New on the left old on the right
Funny, just got mine not too long ago, but think I have the wider one. Draw is definitely airier than the Oddy.
New on the left old on the right
Are these both the same version (v1 or V2)?
The older one I ordered about 2 months ago, the newer was about 3 weeks ago. APO shipping is slow
Both are V2's
V2 I think, better.. it can ground right at the channel. Its only nessasary to use one no res leg to reach the positive.
On a side note .. My oddity has the 510 threads on my kamry just about all the way stripped out in less than a month.. The kamry 510 is plated brass. Not sure if this is common mating a ss to a brass 510, probably, or the threads weren't great on the tobecco... Probably both.. For sure
On a side note .. My oddity has the 510 threads on my kamry just about all the way stripped out in less than a month.. The kamry 510 is plated brass. Not sure if this is common mating a ss to a brass 510, probably, or the threads weren't great on the tobecco... Probably both.. For sure
Last edited:
V2 like Jermy said, plus it has bigger wick channels so you can use 3mm wicks.
SS will win over brass every time. You must be careful to not over tighten when using SS and brass because what ever the brass part is, it will strip out. This happens at work all the time. I'm not too familar with the K100 but does it have an adjustable center pin? If it does loosen the pin, then screw the tank on, then tighten the center pin.
Its a k200 spring loaded center pin.. and extra care was taken, it wasn't over tightened or cross threaded.
As others have mentioned the tobecco oddy threads are terrible. And a 510 (m7x.5) thread chaser is not easy to come by.. I guess I need a ss 510 mod..
As others have mentioned the tobecco oddy threads are terrible. And a 510 (m7x.5) thread chaser is not easy to come by.. I guess I need a ss 510 mod..
I see, I have the Term. I knew the tobecco's were not as nice, but didn't know that they have bad threading. That sucks, I think if it was me I would get a Term also. You might not have problems with a SS mod with it, but at the sametime if the treads are bad enough, one of them might get messed up over time.
Over tightening an atomizer into a 510 is always going to end up trouble. Anytime you have an atomizer with SS 510 screwing into a brass 510 it's just a matter of time before the brass threads get eaten away especially with a heavy atomizer.
Well I just broke 2 clear tanks on my Term in 2 days, damn tank cracking juices After the fact I found this thread on tank cracking juices (newest list is post 391)
http://www.e-cigarette-forum.com/forum/clearomizers/219179-lets-make-list-juices-flavors-crack-tanks-ce2s-clearos-40.html#post9660727
After the fact I found this thread on tank cracking juices (newest list is post 391)http://www.e-cigarette-forum.com/forum/clearomizers/219179-lets-make-list-juices-flavors-crack-tanks-ce2s-clearos-40.html#post9660727
This is a bit of an odd question, but I am getting a total lack of throat hit on Boba's Bounty (18 mg). I was thinking it was my build, so I kept trying different builds.
I finally tried a different juice (Grey Matter from Mister-E, 18mg, 50/50) and the TH is more than adequate. Switch back to BB and no TH. Term V2 and Herc.
Tried a couple of different 18mg 50/50 juices and TH is fine.
Flavor and vapor are fine with BB, just absolutely no TH.
Is there something I can try on a build (have tried micro coils, 29 awg, 32 awg, 36 awg), resistance from .8 ohms to 1.2 ohms.
Is the increase in VG to blame? Should I increase the Nic level of BB? I can't go back to fighting cartos after tasting BB in a Term/Herc, I have to get this working...
Sent from my iPad using Tapatalk HD
I finally tried a different juice (Grey Matter from Mister-E, 18mg, 50/50) and the TH is more than adequate. Switch back to BB and no TH. Term V2 and Herc.
Tried a couple of different 18mg 50/50 juices and TH is fine.
Flavor and vapor are fine with BB, just absolutely no TH.
Is there something I can try on a build (have tried micro coils, 29 awg, 32 awg, 36 awg), resistance from .8 ohms to 1.2 ohms.
Is the increase in VG to blame? Should I increase the Nic level of BB? I can't go back to fighting cartos after tasting BB in a Term/Herc, I have to get this working...
Sent from my iPad using Tapatalk HD
Heavy VG juices have far less TH yes. I vape 80-100% VG generally at 15mg. I tried some juice in a friends PV that was 80% PG and was actually quite surprised at the TH. I personally don't like a lot of throat hit because I generally go through about 6-10ml a day.
How in the world? You need the Legal Vape 4000, LOL.
I go through 6-7mls of 24mg myself... My Term C's and Herc are thirsty little beasts.. 
My Term C's and Herc are thirsty little beasts..
I go through 6-7mls of 24mg myself...
Yes, the are ... but they do like to throw that flavor out.
I have not seen an atomizer best an Ithaka (or it's clones) or Oddy (and it's clones) on flavor and I have tried many.
Vapor is good, flavor is super
Vapor is good, flavor is super
Last edited:
- Status
Similar threads
- Locked
