No, luckyA gate can be fixed and doesn't feel pain lol
neighbor needs drivers ed?
No, luckyA gate can be fixed and doesn't feel pain lol
But shorting to what?Sounds like some of the wraps are shorting
I just measured a Q-tip brand Q-tip with the paper stick and it is 2.53 mmYep. Nope and nope. I've been building those 2 tanks for almost a year now. Never off the 1.6 ohm mark by more than .2 ohms either direction. Usually only vary by <.05. I hit them with a DMM before I put the chimneys on. Then put them on the mod and it reads the same after fully assembled.
My coiling jig of preference for KF's is actually a q-tip stick with the cotton tips clipped off. It's just a hair over 2 mm, but still less than 2.5 mm. I have a coiling tool, but it seems to get in the way when I go to wrap the wires around the screws. And it's partly habit. I didn't have the tool when I first got the tank, so I just tend to do it the same way I always did.
How does that happen? If they were overlapped, I could see it throwing the resistance ff and making a hot spot, but they aren't.To each other
I understand that but putting a 1.5ohm coil in, it's no longer a sub ohm tank.
Unless the kanthal is oxidized it will short when touching.How does that happen? If they were overlapped, I could see it throwing the resistance ff and making a hot spot, but they aren't.
I pulse and pinch to get rid of the hot spots. That usually oxidizes them a lil bit.
I'm poor. I use the Megalo-Mart brand. Not sure exactly what size, but they are just barely visibly smaller than my 2.5mm coil tool. Either way, no way I should get a 1.06 ohm coil off it with 8 wraps. And if I had a short, there would be a hot spot somewhere at the low resistance spot.I just measured a Q-tip brand Q-tip with the paper stick and it is 2.53 mm
I'm poor. I use the Megalo-Mart brand. Not sure exactly what size, but they are just barely visibly smaller than my 2.5mm coil tool. Either way, no way I should get a 1.06 ohm coil off it with 8 wraps. And if I had a short, there would be a hot spot somewhere at the low resistance spot.
Question to the toots, how come I have never seen anyone using a Subtank Mini with the 1.5ohm coils, great for tootling, great price, 4ml of juice, coils last ages and it has a rba deck.. Strange
Or just vape it.I dialed it back a few watts and it works just fine. Was just curious if anybody else had seen the same thing happen before and what caused it.
Or just vape it.I dialed it back a few watts and it works just fine. Was just curious if anybody else had seen the same thing happen before and what caused it.
Well can you believe it, my next door neighbour and her sit on lawn mower just came smashing through my gates and almost took me out while feeding the fish, that could of been messy. Shes not only backed into her own garage in her car, shes now crashed through my side gates, someone please give this woman a bicycle and a push along mower. Why do these things keep happening to me, I put down the paint roller, feed the fish and almost loose my feet and ankles..... I need a vape.
How do you like the ErlK Linda? I always wanted to pick up a cheap one to try out.My coils always seem to be .1 or .2 off of what I was intending. I usually just vape them and enjoy the vape. A few days ago I was wrapping a coil for one of my Erlk's, got distracted, and put an extra wrap or two in it. It ended up being 2 ohms. I haven't vaped anything much over 1.5 in a long time. But I vaped it anyway and for some reason that coil gave me the best flavor. So I might just go ahead and wrap them higher from now on.
Unless you put something like this on your KF 3.1 then it just burns the wick off in the middle of the coil.More wraps means more vapor and more flavor.![]()